Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
When i call the custom-code certify() function inside my code in a secure partition i can build the programm, but after clicking flash/running the secure uart-output prints...
Is there a DTM sample for the nrf52dk_nrf52832?
I see the sample supports nRF52840 and higher according to the docs.
I tried selecting the nRF52dk, and everything compiles...
Hi,
As well know, there have a nrf_delay_us() function can execute very short delay time, but the function can only "delay".
If I want to create a 1 microsecond continuous...
How are the 28-UFBGA pin assignments translated to numbering used to specify I/O pin numbers in the code. Is this as simple as P0.0 => 0, P0.1 => 1,...? I have seen similar...
software:ncs2.5.1
chip:nrf5340
hi professor,
I want to use dtm to test blue RF. After i compile dtm example by vs code and download merge.hex by nrf connect sdk programmer...
Hello,
I am experiencing an issue where ble_nus_data_send returns a value of 0x08. I would appreciate any advice on how to resolve this error.
Symptoms: The device ...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I used UART for communication between...
This is my log output when i connect to my ethernet
this is my prj.conf file
I am building the default AWS_IOT_MQTT SAMPLE. i dont know where i am getting the issue...
I want to implement a network of boards to be placed in a field. We have sender nodes(boards) which will collect data through saadc channels and transmit it to receiver node...
Hello,
i am developing a bootloader with softdevice112 on nrf52805.
I have setup everything and I can see bootloader and app working, just a question about memory layout...
I can't use the I2S api and I2S function in code the compiler says undefined Module , and when i checked the devicetree file there in no definition for the i2s devices
Hello,
I am programming BLE with the nRF52840-DK.
Toolchain Manager: v1.3.0
IDE: Visual Studio Code (VSCode)
SDK: ncs v2.6.0
My implementation goals are as...
With the change from nRF51 to nRF52, the data rate became a minimum of 1 Mbps.
Nordic proprietary radio mode,
nRF51 250 Kbps.
nRF52 1 Mbps,
What is the difference...
Hi everyone,
I working on a project which is a BLE peripheral with Zephyr,
I need to implement the DTM testing for production testing. I created my project base on NUS...
