Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
We are working on our manufacturing process that involves use of the nRF9160. I need a way to programmatically get the IMEI and ICCID in order to register the device...
I'm running a nRF52 device that's built on nRF5 SDK11, and it's remaining that way now due to regulatory reasons. My application needed to be updated to support bonding, and...
I have a nRF9160DK board running asset_tracker_v2 on a nRF9160 custom board. V1.7.0 loads and boots fine but when I use V2.5.0 the boot fails as shown below. The only change...
Hello, per the product specification, I see that the nRF52832 CIAA variant requires a shunt 1.0pF capacitor and series 3.3nH inductor.
Is this recommended regardless of...
I have configured NRF52840 as coordinator ,EFR1 (ENDDEVICE) and EFR2(ENDDEVICE) as end devices. These 3 devices are connected in network.EFR2(End device )continuously sending...
I would like to understand the issue of frequency offset calibration in RF signals, I have viewed the
Case ID: 309794
nwp_006.pdf
I would like to know if I can do...
Hi,
We are working on BLE MESH using nRF52840. We are trying to put nRF52840 into deep sleep mode. The deep sleep current is about 210 micro Amp. Further, the current is...
Hi,
I have a coap server/client system and when I send a provisioning request from the client I can see the server is sending the reply. But my 'on_provisioning_reply (...
Hi,
I'm using SPI4M on nRF53 and came across it's errata, but I didn't get where to call the workaround functions.
The workaround is to call the below line upon enabling...
I have a custom board with an nRF5340 on it. I'd like to offload BLE operations to the network core using the RPC library to control it from the application core.
The documentation...
Quick Background
The spi_transceive_cb() function in Zephyr takes two buffer sets (among other arguments). One buffer set to TX and one buffer set to RX. You may pass NULL...
Dear All,
We want to test the maximum distance of Broadcast audio gateway using nrf21540EK with nrf5340 Audio DK.
And we want to output the rssi info periodically on the...
We are running out of space for DFU, thus changed start address from 0x77000 to 0x6E000
After reading related documents, it seems I had a problem
SD_MBR_COMMAND_COPY_BL...
in devacademy there are mqtt and gnss sample. when I put the mqtt configs to gnss sample. give an error. I did not add main code yet. just only put configs and cmake.
after...
I came across a client example that use the
I read about BT_GATT_SUBSCRIBE_FLAG_VOLATILE
How I know if the subscription is not saved on the GATT server side (which...
