Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello !
I'm struggling a bit with the USB HID boot protocol, I have a lot of stack overflow error when trying to do operations while in the get_report callback.
I know...
I'm embarking on a new project involving a sensor network of up to 3000 devices within a warehouse for industrial monitoring, and I'm considering an OpenThread network-based...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
Hi, I'm currently using nrf52840 MCU for product development and almost finished my project. What I want is when producing a product, I want to compare the checksum of the...
I am trying ADC readings for connecting my sensors. To better understand and see the values, I have made a simple connection with 4 10k Resistros in series, VCC on top and...
I am working on an nRF52832-based project and I am encountering an issue with achieving low sleep current. Despite setting the TX power to 0 dBm and the advertising interval...
I am thinking of using the sample source code of nRF5340 Audio to realize LE-Audio on a board created by our company.
I have written the source code of nRF5340 Audio to...
Hi, I am pretty new to programming with NRF boards and I've hit a bit of a roadblock.
I started with the BLE Event Trigger example and I have managed to retrieve BLE advertising...
HI Noridc
I am developing with nRF5340, and I need to proceed with DTM test to verify the chip in the production process.
I am currently using this routine C:\ncs\v2.6...
Hi, I'm working on a ble peripheral that uses nRF5340, NCS recently upgraded to v2.6.1, Zephyr v3.4.99. The net core is running the HCI RPMsg controller sample as it is. In...
Greetings all. I am troubleshooting an issue on my BLE sniffer setup. While I don't 'think' this is causing my actual current failure (Wireshark not detecting COM6) I wanted...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I modified the code to change the quantization level of the I and Q data received by the receiver...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I added CONFIG_BT_DF_VS_CONN_IQ_REPORT_16_BITS_IQ_SAMPLES=y in the direction_finding_central...
