Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Greetings all. I am troubleshooting an issue on my BLE sniffer setup. While I don't 'think' this is causing my actual current failure (Wireshark not detecting COM6) I wanted...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I modified the code to change the quantization level of the I and Q data received by the receiver...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I added CONFIG_BT_DF_VS_CONN_IQ_REPORT_16_BITS_IQ_SAMPLES=y in the direction_finding_central...
Hello Team,
Just to give you a background , I am working on a project using the NRF Connect SDK and want to run my application from external flash memory. Specifically,...
Hi,
We have a custom board, where we assigned the following pins for SPI4M instance, and the intention is to use it with 32 MHz:
SCLK = P1.15
MISO = P1.14
MOSI = P1...
I'm working on a tracking project using the Icarus IoT Dev Board (nRF9160), which employs both NB-IoT and GPS functionalities. During the project, I encountered an issue where...
Hi,
I am developing the matter example device. I would like to test the connection to Google Home App. I see in the documentation that I should first create a project in...
Hi Support Team
We have got the nRF9151 DK and want to start the development. Could you provide us the nRF9151 specification file and the hardware design reference file...
I am having nrf52833 module where I am attempting to run buttonless DFU for this I have made some changes in ble_app_uart_pca10100_s140.hex and have used
SoftDevice as...
Hi,
I got a brand new nRF52832 DK today and wanted to program it but the USB is not recognized at all therefore the nRF Programmer shows no programming option.
I connected...
Trying to integrate the serial part of the example code for use with a custom nRF52840 board. The problem is that I'm getting an error in uart_callback_set(uart, uart_cb,...
I use `west debug` to start `gdb` for debugging nRF5340DK
when I use `west build` to update the image, I use `load` command inside gdb CLI, the new `zephyr.elf` is loaded...
I don't know if this is a hardware or a software problem. My nRF52832 code runs correctly on a PCA10040 development board (UUID = E9:4A:AF:04:D2:16). My custom hardware advertises...
My software sent 2422, and I saw it on the net. 2417 also has one.
And the same goes for everything else, which is basically 5M off.
What is the reason?
Hi all,
I am working on troubleshooting intermittent application resets with an nRF52840 and nRF Connect 2.6.1. Codebase is small, complexity of the project is still small...
