Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
This is my first time using nRF connect and Visual studio but I have been following through first the Fundamentals course on the Dev Academy using the nRF52840 DK with...
Hi
I found some Bluetooth send the data unstable problem after i enable the usb cdc acm function. Can you help me to
check my setting that has missing or not thanks. ...
Hi,
I am adapting the Azure IoT example for use with the nRF5340DK and nRF7002EK.
The configuration is:
- sdk: nvs 2.6.0
- example Azure IoT hub
Initially, the getaddrinfo...
Hi Support Team
We test the nRF52840 power consumption of Thread Device follow the below links document.
(+) Analyzing power consumption in Thread Sleepy End Devices...
Hi,
I'm trying to increase the UART buffer size for the asynchronous UART API, but I'm encountering an error. When the message size is set to 255, I can successfully receive...
Hello all,
I config nRF52840 dongle P0.24 and P0.22 as GPIO_OUTPUT. But when I change their value, they are always 0.
I use the same way to change other pins such as P0...
Our product works fine. But I was wondering if we should be completely disabling the NRF_LOG functions for production builds. I suppose it could be using some power and processor...
I'm having a really frustrating time with a custom 7 segment display board I'm developing for scorekeeping. It seems to be successfully flashing using a Segger EDU mini, but...
Hi, I have a nRF52840 DK and I tried powering it with a USB cable. The issue is when I look into device manager the device is not showing up, and when I try connecting the...
Hello !
I'm struggling a bit with the USB HID boot protocol, I have a lot of stack overflow error when trying to do operations while in the get_report callback.
I know...
I'm embarking on a new project involving a sensor network of up to 3000 devices within a warehouse for industrial monitoring, and I'm considering an OpenThread network-based...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
Hi, I'm currently using nrf52840 MCU for product development and almost finished my project. What I want is when producing a product, I want to compare the checksum of the...
