Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
We are developing on a nRF52832 MCU and we tried to enable MPU on the whole RAM region (addr: 0x20000000, size : 0x10000) But when we create a new MPU region around...
Hi,
So I have seen there is a clean -up option to set the architecture core HW registers to their warm -reset values as specified by the architecture before running the...
Hello everyone,
using Segger Embedded Studio, I encountered an issue with the TWI libraries. My device consists of a custom PCB controlled by the nRF52840 (programmed with...
A simple and maybe trivial question. When in a thread I wait data for example with
is it like call continuously the k_yield()? How the api above works in the underhood...
Hi
is there any example or Tutorial to start from the beginning stage of developing Multiprotocol (BLE and Thread)?
I've tried searching many articles still unable to...
Hi,
Chip: nRF52840
OS: nRF Connect / Zephyr: v2.3.0
Problem: Saving coredumps to external flash
We're trying to add a bunch of debugging features to our firmware before...
I am using the PCA10040 nRF52DK board
I want to connect the UART RX and TX pins of the nRF52832 to my target CPU
I have cut the connections at SB16 and SB14
I can see...
Hi Sir,
As we know, Matter 1.3 supports Electric Vehicle Charging.
Do we have any plan to support the example of Electric Vehicle Charging?
If yes, what is the time...
Hi, We are using a Segger JLINK to program a nrf5340 product using the SWD interface. We have been successfully programming units using a design where there is a 100k pullup...
When we try to test the stability of the UARTE peripheral, we find that when inserting and removing the RX pin, the uarte_handler callback function is very likely to goes...
What is the recommended UART SUSPEND sequence to use the PM_DEVICE_RUNTIME? I am having trouble using the PM capabilities with the UARTe driver. I am developing on the 52833...
Hi,
I am trying the https://github.com/NordicDeveloperAcademy/bt-fund blefund_less1_exer1 using nRF52840 DK. I am able to connect but not able to detect button press. I...
SDK:17.1
application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble I want to know what operations will be performed when...
Hello,
I saw in an old forum thread ( https://devzone.nordicsemi.com/f/nordic-q-a/79412/lwm2m-amount-of-object-instances-limited ) that block transfer was not fully supported...
