Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi
Spotify 128 kbps aac stream is about 16 bytes per ms. Ble should support 31 bytes per packet.
So can I stream 16 bytes ms over lte m to nrf 9160 then via uart to...
Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
Hi,
A veteran of nRF5 SDK but new to NCS.
I tried to run tx_rx_non_blocking example from the latest (2.6.1) NCS SDK, but can't get it to run (nR52840DK)
It seem...
Hello, I recently set up an nRF52840 with the nRF7002 evaluation kit using the WiFi station sample. However, during the build process, I noticed that it consumes a significant...
Hi,
I'm integrating an external SPI flash W25Q32 with the nRF52840 using the NOR FLASH driver, but it's not functioning properly as the MCU log indicates an MPU error. ...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it. ( developer.nordicsemi.com/.....
Hi All!
I have a question, i am using nrf52833Dk as an extended advertiser and nrf52840 dongle / 2nd nrf52833Dk as a scanner using the BLE desktop App (nrf connect for desktop...
I am not able to send 25 array packets each second. array size is 244 bytes I am reading the sensor data continuosly and every 40 ms i am sending the data to bluetooth using...
Hello,
I am on a development team utilizing Nordic Board NRF52DK to connect to a custom NRF52832-based board/external device via debug out on the Nordic Board NRF52DK, the...
Hi,
I'm experimenting with an Acconeer XM126 board which has an nRF52840 processor (and an Acconeer A121 chip) and a Bluetooth antenna (and an RF antenna too). I'm deploying...
Hi all.
I have made myself a board which has a module with the nRF52833 chip embedded onto it. It's effectively a board with a set of switching regulators on it to drive...
I am using NRF52833 and trying to setup DFU specifically for OTA.
As experienced in other threads the size limitations are there
Secure_Boot builds creating slot partitions...
Howdy guys,
I am using an nrf52840 and SDK version 17.1.0 alongside Keil. I just upgraded from using the arm compiler version 5 to 6, which required me to switch from the...
Hi,
I have an implementation in which two boards communicates through ble and i want to measure the throughput of both. The behaviour that I see is that increasing the connection...
Hi,
I have a Tuya FingerBot Plus and when using the Zigbee Shell sample:
1.I can 'click' the finger using a ZCL command
2. I can't change the 'finger mode' from 'click...
