Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
When I load the firmware, the firmware starts running fine.
but once I power off then on tue device the firmware crashes at a certain point while in the main loop with no...
Hi All,
As part of the software development, we are required to use an automatic tool for Code Coverage.
We use an nRF52840 device, C language and 15.3.0 nRF SDK on...
Has anyone succeeded in BLE bonding with a Philips Hue lamp or a Hue smart plug with a nRF52? Directly with BLE, without a gateway. I suppose I have all the rest figured out...
Mcuboot manages firmware versions and is able to avoid fw downgrade.
Is it possible to define a product id to avoid to exchange fw for different product of same manufacturer...
Hi,
I want to prepare the scrip for Wi-Fi radio test commands. I am testing the RF performance on nRF7002dk and in order to test the each channel i have to run the below...
Hi,
We have run into an issue when debugging code with the nRFconnect sdk debugger. A breakpoint set in an interrupt service routine is not hit, however, we can see through...
Hi,
I have a piezo microphone with analog output and would like to record from it using the Line In AUX on nRF5340 Audio DK.
Currently, I am using the break out pins...
Current goal is to be able to program, and upgrade with the radio off, and the only connection as a UART.
But I'm both overwhelmed by the number of options (DFU, SMP, and...
Hardware: nRF5340DK
Software : nRF Connect SDK v2.6.1 (any reasonably up to date is fine)
Hi,
I'm new to Zephyr and Nordic and I want to make an example multi-core application...
We have a custom board based on the nRF52805 that does not have a HFXO or LFXO. We are using NCS 2.6.1.
When the firmware thread is idle, current consumption as measured...
Hi,
TLDR: Tried the new BLINFO feature on an existing app, upgrading to 2.6.1 SDK (Zephyr 3.5.99). App does not boot after merged.hex flashed.
So we are updating our project...
Hi,
I am trying to figure out how to change the automatic gain settings on the on-board microphone. It is connected via its I2C to the hardware codec, but apparently not...
Hi i would like to connect an led with mcu (NRF52832-QFAA-R7) and control the led with PWM. while investigating in datasheet i found "Three PWM modules can provide up to 12...
Hi there,
As I’m currently evaluating our GNSS implementation, I’ve encountered some discrepancies in your documentation.
My inquiry pertains to the optimal implementation...
I'm using 2 nrf52840dk, ncs2.5.0; running the central_uart and peripheral_uart examples, I want to know how to send a string without pressing the "enter" key. For example...
