When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello, We have registered our project with Nordic. Our project ID is 60803622472. Project title: DECT NR+ Star Topology Sensor Node Evaluation with nRF9151 We would like to...
Hi Nordic team!
I haven't been able to implement the joiner functionality on a Thread network with nrf52840. I'm using the nRF52840-DK as the leader. For the DK, I follow...
Hi all. I am testing the NPM1300 with nrf54l15 using vallina Zephyr. I've setup device tree for npm1300 to generate interrupt on its GPIO0 when there is event.
When Vbus...
Hello Team,
We are evaluating an architecture where an NXP MIMXRT700 EVK powers an nRF9151 DK externally while using the nRF9151 DK as an LTE modem.
Hardware:
MIMXRT700...
Hi，
I use NCS 3.2.4 and 54L15 DK. In the DFU target, I added configuration
and also added the following content in dfu_recover function.
After the distributor...
Hi
We are using nRF5 SDK v14.1.0 and soft-device S132 v5.0.0 for our device which are already in production.
For function/feature improvement in this devices, we like...
Hello we are trying to use nrf21540 RF FEM with nrf54L15 using baremetal sdk (sdk-nrf-bm). We are able to use Softdevice S115 for BLE communictions. We now need to integrate...
I am building a multi-device walkie-talkie system using DECT NR+ on the nRF9151. I want to split devices into isolated communication groups by assigning each group a different...
Hi everyone,
we are running a Cloud-to-Cloud scenario where we use the Assisted GPS API.
https://api-docs.nrfcloud.com/#tag/Assisted-GPS/operation/GetAssistanceDataLegacy...
Hi,
We are developing on nRF52832 with NCS v2.9.2 (Zephyr) on a custom PCB (LDO, no DCDC, 32 kHz RC).
On the same hardware, our nRF5 SDK firmware shows much lower average...
Dear Nordic Team
nRF54L15 is advertised as supporting BLE 6.0. our product is a type of charging case,I would like to know if we need to pass BLE 6.0 certification?
If...
Hello,
Quick one:
https://docs.nordicsemi.com/r/bundle/nordic-mcp/page/index.html seems to be broken. I have a myNordic account and everything. I tried on two different...
I want to adjust the HFXO capacitance using INTCAP.
When the XOSC32MTRIM.SLOPE (chip-specific factory calibration value) is small, the resolution of INTCAP becomes coarse...
In our project we have functions for outputting a single frequency via PWM for an indefinite amount of time until we call a function to turn it off. See attached code.
...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
