Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, I am trying to test multi_sensor example from Zigbee and Thread SDK 4.2 using official Nordic nrf52840DK with few Zigbee hubs. Example is located in \examples\zigbee\experimental...
Hi
My thingy91 does not appear in the Connected Devices list in VS Code. I've tried everything now.
What's the prerequisites for getting this to work?
Do I have to install...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 and want to use MCUBoot with Direct-XIP.
Using the hello_world sample project, I added MCUBoot.
In the MCUBoot prf.conf...
I have issues with my NRF5340DK devices that I'm hoping to get support on. Several devices appear to be bricked, stuck in a boot loop or otherwise unable to program using...
Hi, I'm hoping someone could advise on interfacing with the T2 LC3 codec included in nRF Connect.
The context is I have stereo I2S microphones providing 24-bit 2's complement...
Hello, As part of a student project I am looking to learn about Nordic technologies for BLE and ANT. The goal of our end of study project is to provide an extremely accurate...
If I would like to add Bluetooth capability to the nrf9160, can the nrf5340 be used as a "companion" MCU?
Would be great if there is a pre-build firmware for the nrf5340...
Hi,
I am trying to write a program that connects my phone to my nRF52840-DK board; I then send one of two commands from my phone, then the nRF52 will respond accordingly...
Hello,
Recently, in my organization we have decided to transition from nRF5 to nRF Connect SDK and while going through this process we noticed an issue with the source control...
Hello, I am trying to get the peripheral_lbs example to unpair all devices (delete all bond informations) using VSCode and nrf connect sdk version 2.0.2.
I tried using bt_unpair...
As part of the NCS install, in the ncs\vx.y.z\Zephyr\doc folder there is a ton of Zephyr documentation (more then 13MB) in .rst format. How do I use this instead of the online...
Hi all
I've tried to build the nRF5340: Multicore application on different host platforms using the nRF Connect SDK v2.1.0. It worked without any problems on Windows and...
Hi,
I'm using NRF52832 with s132 softdevice for a low power project. I notice that when running firmware with DFU Buttonless, the SoC consume more power than without it...
Hi,
I'm trying to reproduce the fatfs example on a nrf52840 DK and Sandisk micro SD card that's plugged into a Sparkfun Transflash breakout board. I can't seem to mount...
