Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
I am developing a product with nRF52832 in which we need to use the COMP module. We need to route the RESULT signal directly to the RX input of the UART, or to an output of...
Hello,
after upgrading to SDK15 and using the new crypto functionality I experience some weird behaviour during bonding.
Our SW is the peripheral and I am starting the...
We would like configure our device with a public addr instead of the random as is default for NCS/Zephyr. We are currently on Zephyr v3.1.99 and NCS 2.1. I have tracked down...
Hi, https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.1.0/nrf/ug_tfm.html#limitations states that "Firmware Update Services" are not supported. Does it mean that in case...
Hello,
I have compiled the Zigbee ZBOSS NCP HOST on an ARMv7 (32-bit) architecture according to the docs ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/zboss/3.11...
Hi all, I've searched through the devzone but unfortunately my issue is never mentioned.
The problem is: my nRF51 project is converted to a nRF52 project. Pins are all re...
We have a need to use 802.15.4 multiprotocol with BLE, we currently use the 52840 for several products. This uses older SDKs and the 802.15.4 Radio driver with our own MAC...
nRF5 SDK SD140 Using the nRF Connect Android app with the DFU utility, looking at the log I send the Enter Bootloader request and get a thumbs up back (op code = 1, status...
Hello, I want to display the "info button" on the Bluetooth menu in iOS. What configuration is needed on BLE to display it and some options like Disconnection, Forger this...
