When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
hello!
I want to use Jlink to download code to a NRF52840 chip as MCU development board, but the number of pins and pin spacing of my Jlink are different from it. So I had...
Hi, Nordic support,
I have built success with the example "nrf5340_audio" set the gateway mode. when I run the example into my board "NRF5340 Audio DK" I get this error...
Hi,
I'm trying to use the nRF9160-DK(Ver.1.0.0) for LTE communication and GPS location information acquisition.
I found a list of LTE antennas at this URL. However, I...
We are using NRF5 SDK 17.0.2 on an NRF52840.
I am implementing a bootloader update procedure. Our updates always store the new image in external flash. The spare space in...
Hi,
I'm interested in using this AT command to upgrade my nRF52840. But I'm not quite sure what to do exactly. I'm using nRF5 V17 SDK on nRF52840. what should I provide...
Hello,
I'm thinking of increasing the transmit strength of my peripheral device using the function provided below.
sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV ,...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
I recently installed the toolchain on M1 Mac using the automatic installation in the toolchain manager.
However, I noticed that the toolchain manager installs x86 variant...
Developing on ncs 2.1, using vs code and nrf connect extension to debug an application running on nrf 9160dk
I am connecting to aws iot core in a similar fashion as your...
Hello,
I have my BLE Gatt Peripheral application working and running.
I am developing a reader that reads BLE credential.
Application is complete. I flash the .hex file...
Hi
I have configured nrf52840 on my raspberry pi. I want this dongle to stop pairing to other device once connected and also most importantly stop broadcasting once it is...
Hi everyone,
currently I am trying to migrate a project from Segger Studio and SDK v1.8.0 to VS Code in combination with the SDK v2.0.0.
For the Project we are using a...
Hello,
We have observed some issues with downloading firmware update over HTTP over NB-IoT. I'm aware that using TCP over NB-IoT is not recommended, but it is technically...
OS: Windows
NCS Version: v2.0.2 Installed using toolchain manager
IDE: VSCode 1.70.2 + nordic-semiconductor.nrf-connect-extension-pack 2022.5.1
I have applications...
