Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi dear all,
I testing smp_svr example on nRF5340DK board , I add bluetooth dfu in project and download into the board .
Use nrf connect try to update, the two update...
Hi, I was trying to test the location sample on my custom board that has an nrf9160 chip. I did everything in this link: https://docs.nrfcloud.com/Guides/GettingStarted/Devices...
So we have our own bootloader project, was trying to get this to work in Segger Studio v6.34 Mac OS Apple Silicon and it would always fail to boot the DfuTarg, the BT would...
Getting linker error "undefined reference to `nRFInitialize'"
Any help would be appreciated, thank you.
T he file 'ses_startup_nrf_common.s' included in project .
Contains...
Hi All!
I tested the central & peripheral_hr_coded examples.By using Nrf connect sdk version 2.0.0 /2.0.2 ,nrf52833DK's. Is it possible to add a feature in the example that...
I am working on implementing a BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED advertising setup.
I would like to minimize the current spike transients...
Hi Team We are working on NFC for our new product. When we measure the power level each GPIO we don't reach more than 700mv. Changing the antenna to a larger antenna did not...
Hello,
I have enabled NRF_LOG over RTT but I get flooded by the same message until my application crashed.
For example:
I get continuously:
what am I doing...
Hello List,
First some context: I am working with SDK 17.1.0 on a nrf52840 (arduino nano ble).
Created a variant of the ble_app_uart example and want to add pairing/bonding...
Hi,
I am aware, that I the PDK is deprecated and I plan to use a nRF5340-DK in the near future.
However, I would like to make use of the PDK I have sitting around and...
Dear Mate,
I am trying to build and flash a program by using (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com...
Dear all,
I'm using nRF52832 and using timers to turn on/off GPIOs.
I saw that timer0, 1 and 2 has 4 CC registers.
Right now, I'm using timer0 like this:
1) turn...
Hi team,
I have some doubts regarding mcuboot behavior on firmware failure.
1) Consider the situation I have flashed a new image , it will get validate before mcuboot...
Hi,
I'm trying to use XIP on our custom board running a nrf5340 with a different Flash memory than the one on the nrf5340-devkit.
The XIP worked on nrf5340dk, but now...
Hi,
I have an nRF9160 device which is going thru PTCRB cert. We are doing TRP/TIS and nRF9160 won't connect to the Anritsu MT8821C. Basically it tries to connect and just...
