Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
My set up is nRF52832 with a board very much like the PCA10040. The SDK is version 16.0.0. I am using Segger Embedded Studio version 5.60 and I am using the GCC compiler suite...
My goal is to have my boot loader write a constant value to RAM and have my applicaton read that same location and retrieve that value.
I am using the stock boot loader...
Hello,
I'm creating a BLE project with a couple of custom services. One of my simple characteristics in a service is a string. When is_value_user = false everything works...
Hey! I am starting my studies in the BLE protocol and I would like to send the ZE03 sensor data through the Nordic UART Service (NUS).
The sensor has 9 bits: 8 data bits...
Hi, I have made a 9160 board, below is the schematic diagram ：
I donwload this example in it, " ncs\v1.9.1\nrf\applications\serial_lte_modem", and send AT command to test...
My Windows app sends command though Nordic UART service to nrf52832 device. Does nrf52832 need to send ACK to let Windows App knows it has received command?
Hi,
I'm using a nrf52832 board. In this case, updating the bootloader is necessary. So, does mcuboot have a way to update itself? , and if not, what alternative method of...
Hello,
I'm trying to move from nRF5 SDK with nRF52840 to NCS with nRF5340 and experiencing a lot of problems replacing the nrf driver functions with nrfx.
Thanks to...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Segger Embedded Studio 4.16
Aim: Controlling...
Hello everybody
I'm trying to initialise an advertising module for my project.
When using the macro for creating an advertising instante I get the following:
After...
hi,
In my application, which was based on nRF_SDK_Thread, to check my node's connection with the Border router, or to know whether the border router is present or not...
Does the on-state current consumption I. E. 1.9 mA remains the same while taking different readings? Ideally, it should come the same while taking different readings. But...
Hi,
I need to upgrade the bootloader i.e mcuboot . so I decided to use primary immutable bootloader and secondary upgradable bootloader as per below link https://developer...
Hello,
I use SDK16 and softdevice S140. I want to use UART to upgrade firmware. Do you have sample code for SDK16? Do I need to install python and nrfutil on my computer...
