hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
My query is:
1. Is it possible to access the azure using WIFI network in above application?
2. After knowing the IMEI using AT Command, in response to which event should...
I am getting more current consumption when internal pull up resistors of nRF52832 are disabled and external pull up resistors of the slave sensor are enabled as compared with...
Hi,
Currently, I am building an application with Bluetooth mesh and I tried to use Zephyr's logging v2 modules. However, when I build it I get MPU-fault errors at boot....
Hi,
I saw in ozone that SW crashed with hard fault explained as escalation of exception that was not enabled.
How can I enable all exceptions to see the exact reason of...
Hello, I'm using nrf52833, pca10100.
My project is based on 'ble_app_uart', and I added buttonless DFU project.
this is ble_dfu_buttonless_async_svci_init() function...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i cannot seem to select nRF Connect SDK when creating application in vs code. i already install the nRF Connect SDK v2.0.0 from the toolchain and the nRF Connect Toolchain...
I am trying to build a example program in KEIL for the nRF52832 QFAA device. When I sart KEIL the program shows a massage that says the nRF_DeviceFamilyPack.8.3.1 is required...
Good day to all I am trying to change the Application on a device with an nRF52832 chip with an existing firmware. To do this, I use nRF Connect for Mobile 4.25.3. From the...
I am developing GATT Server Reader Firmware usng nRF SDK COnnect using NRF52840
I have implemented two services in reader FW in two files say: service_a.c and service_b...
I have tried installing the nrf connect 3.11.1 on 2 different windows 10 machines. Both are clean windows 10 installs. The hard drives were wiped and windows reinstalled....
Hi,
the following event is generated when I connect two or more nRF9160DKs to a Windows machine: "Disk 2 has the same disk identifiers as one or more disks connected to...
1. 2. 3.
I am using the ble_app_beacon example as the starting point for my project. I am working on a project where a number of beacons will advertise its identity and...
How do you enable any of the i2c peripherals on the nRF9160 dk boards?
I tried changing the device overlay to the code below:
& i2c0 {
status = "okay" ;
compatible...
Hello,
I have a project that uses JWT.
When migrating from nRFConnect SDK 1.6.1 to 1.9.1, build failed with message: multiple definition of `default_CSPRNG'
The error...
