Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I figured that a slave select is configured in dts as: However, when there is a need for multiple slave selects, slaves have to be managed explicitly as informed in...
Afternoon folks,
I'm new to nordic, previously a TI developer. I'm still getting my head around the SDK. I've unfortunately been left with some poorly organised, very-un...
Hi
I have a clean sample problem
1) Installed a clean install or nRF connect v1.9.0 at c:\nRF
2) Installed the VSCode as recommended
3) Pressed Create a new application...
Hi,
I am using an nrf52833-dk for development, and I need to work out interrupt based SPI. Can you kindly point me to an nCS based sample project for interrupt based SPI...
Dear Concern,
I want to keep my nRF52382 module in low power mode during non operational condition. During the TX and RX condition it has to wake up from the sleep mode...
Hi Team,
I tried the blinky example for the nRF52833 DK with the nRF5_SDK_17.1.0_ddde560 . I am using Segger Embedded studio for ARM V5.62 64bit – Non Commercial License...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
The program is created by referring to the whitelist of "ble_app_hids_mouse" which...
1. in the file "Core_v5.2.pdf"
"The LE system operates in the 2.4 GHz ISM band at 2400-2483.5 MHz. The
LE system uses 40 RF channels. These RF channels have center frequencies...
1. I'm runnig the asset tracker fine with nRFCloud. When I run the cloud_client, I get this log:
*** Booting Zephyr OS build v2.7.0-ncs1 *** W: Already initialized. Nothing...
Hi,
Referring to this - https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/devicetree/bindings/net/wireless/nordic,nrf21540-fem.html I understand...
Hello everyone! I'd like to implement the nrf52-ble-image-transfer-demo with a nRF52840 Dongle, for a small low-power image transfer application. My question now is, how do...
I am trying to use Visual Code environment (on macosx Intel macbook pro) to program nrf52840 dongle.
The dongle is found and programmed with using nRF Connect for Desktop...
Hi Nordic，
One of my customer has a problem about 2M phy.
They use 52840 connected with IOS via 2M phy.
They set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL both to 20...
Hi, I'm working on nRF9160 with Zephyr (SDK 1.7.1) and one SPI device. I analyze CS signal with correlation to SPI SCK. Is that normal that CS signal stays low much longer...
