Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
I am trying to sample a large quantity of sensor data from the nrf52840dongle as the server and the nrf5283dk as the client. I have used the peripheral uart and central...
Hi all,
So I want to give you a full description about what we are doing because we could not understand what we did wrong.
Our DK : dk-51
Soft Device : S130_v1
Our...
Description:
I try to initialize a SPI device in my nRF52DK through the Zephyr‘s driver(drivers/spi.h).
Code seems correct when compile and I got no error when build the...
Hi, I am new to Zephyr and Nrf, I am trying to replicate the event manager arch from asset tracker v2 but I am stuck in the setup. I am trying to use the logging capacities...
I am working on the Electronic Braille Display for visually challenged persons.
Our device will communicate with Voice over service on the laptops and smart phones using...
Hi,
with %SHORTSWVER: nrf9160_1.3.1 I am getting:
AT%CMNG=0,3,4,"test1234" OK
AT%CMNG=0,3,3,"30313233343536373839303030303030" OK
AT%CMNG=1 %CMNG: 0,6,"0606060606060606060606060606060606060606060606060606060606060606...
I have a single sample of the new nRF52840_XXAA at hand on our custom board. I'm trying to do a --recover with nrfjprog. As the log below shows, nrfjprog recognizes it as...
Hello ,
I m using SES v5.6 and NRF52805 ,ble_app_uart ex (nRF5_SDK_17.1.0),
Requirement -need to wake up and reset ( or start advertising again) from sleep mode ,when...
Hello,
I have adapted some of the ESB proprietary Protocol from the NRF SDK into my own project without installing the SDK directly; however, complete integration seems...
Hi Team ,
In my application , i am using RTC1 for RTOS and RTC2 for Running a time calibration andRTC0 for Softdevice but parallelly i need to add Lbs service which includes...
Hi there,
I wanted to test Matter/Thread networks using the nRF5340DK I have.
I downloaded the nRF Connect SDK through the Toolchain manager.
I tested the blinky app...
Hi,
I have an unusual requirement where the current constraint device needs to the controller and passively scan. My understanding is the best way to estimate the current...
Hi Nordic Semi
I have implemented a basic BLE peripheral on a nRF5340 using the nRF Connect SDK 1.7.0.0.
The product we are developing have strict power consumption requirements...
I've been able to port the DFU process into a C# app running within a Linux gateway.
I'm using the buttonless without Bonds service to enter DFU mode.
The problem I have...
I am trying to find information on this and it is not clear.
Is it safe to perform FDS read operations (i.e. fds_record_open(), fds_record_find() and fds_record_close()...
