When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi，I am trying to use nrf52832 to drive the ad5940 chip, but using the function in the SPIM driver library to initialize the ad5940, I have been unable to get the ID of the...
Hi Nordic,
i'm using a nRF51822 based board (Adafruit Bluefruit LE Sniffer, PRODUCT ID: 2269, https://www.adafruit.com/product/2269 ) and could sucessfully update to nRF...
Hi
Sorry,This case is the following of case ID: 278538, I didn't find a reply button option in case ID: 278538,So I recreate a new case, I failed to create a new application...
Hi. I am trying to get the gsm modem sample project to work with an nRF 5340 app and a Nimbelink LTE modem, NL-SW-LTE-TC4NAG. The only change I made to the project was to...
Hi Nordic Support Team,
First sorry for basic questions.
I'm learning the basic hardware setup & Linux driver configuration things to setup & configure the MCU(i.mx6)...
Hi, i am Agustin.
I am working with Thingy 91. I am using the Asset Tracker V2 application to upload data to AWS. I have a problem with "Build Solution".
Hi , I got a problem when testing nrf53 qspi signal using a logic analyzer ,with a non-blocking init of qspi and a 4 Byte write , codes are below:
I got a word align problem...
Hi Team,
I want to use the Nrf52840-CAKK-R7 chip to fabricate a PCB board. And communicates with other chips by SPI interfaces.
Now, I want to select the GPIO ports by...
Hi All,
I'm using nRF9160DK PCA10090 Version 0.9.0 and I want to update the Cellular Modem Firmware using nRFConnect 3.8.0 Programmer v2.0.0. Debug Probe is switched to...
We have a timer with a number of variably sized intervals as illustrated below operating on a single capture/compare channel (CC):
Currently the method we use to set the...
Dear all,
In the datasheet and online it is mentioned that the DAP (Debug Access Port) is activated when a programmer is attached. Moreover, it can happen that the programmer...
Hello all,
I am trying the get working the example project nfc_writable_ndef_msg on a nRF52832 with the nRF5 SDK.
I have tried the others NFC examples were most are based...
Hi I am trying to update the connection interval of a peripheral device (nRF52840 ) and I have followed the steps mentioned here .
After Enabling the ble on the device I...
Hi Team,
I have several nrf52840 developing boards for developing BLE Mesh applications.
Now, I want to use SPI interfaces. I didn't find any instructions or examples...
