Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi.
This question is to confirm again about below.
Is it possible that implement multiple advertising sets, some of them would be 1M and some would be CODED PHY. And...
I'm trying to set up VS code to use it with the NRF Connect SDK. I've created an application from basic/blinky example. My problem is VS code can't resolve any inclusions...
OK, like many people moving across from a different IDE/SOC environment, I'm finding navigating my way through setup and programming with Nordic SOC, even of simple tasks...
I've run into two oddities with the Connected Devices feature of nRF Connect for Visual Studio Code and two different nRF52840 dongles that are connected via a J-Link. In...
Hi,
I try to use zgp api and first try to call zb_zgps_delete_all_zgpd() but I receive an error from linker:
undefined reference to `zb_zgps_delete_all_zgpd'
Is there...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am using openthread protocol...
We want to use GPIO_12 as a wake up pin. (High -> open uart, Low -> close uart) Also, we have a timer and timeout set to 500ms. When we pull GPIO_12 to high, it seems not...
I'm working on NCS 1.6.1 for both nRF52840 and nRF9160.
I'm trying to put my devices into sleep mode so i reviewed some related tickets and found following ways.
NRF_REGULATORS...
Hello,
I am quite new to NCS. I am trying to sending UART data from nRF52dk_52832 to PC.
The example is nrf\samples\peripheral\lpuart.
If I enable the example with CONFIG_LOG...
Want to realize a function: stop broadcasting after a broadcast, update the broadcast content, and then start broadcasting again after the specified timeout. How can I judge...
I am using the nRF5_SDK_17.0.2_d674dde and the nrf5_SDK_for_Mesh_v5.0.0. I am using the nRF52 development kit and I want to know if I can use the flash fstorage on the mesh...
Hi. I am working on a project and am planning to offload most peripherals to the net core; a few are listed below. Is this a bad idea? I realize I might run out of flash memory...
hello ,
During my twim0 initialization, I have configured clear_bus_init as true and hold_bus_uninit as false. But i always get hold_bus_uninit as true.
then I dig into...
Hi!
We would like to install approx. 2000 pcs BLE devices in a mesh network. The device density is quite high (2x5 meters matrix, same level, no objects).
I think only...
