When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
Hi! I'm trying to save some variables after a watchdog reset for debug why my application hangs up.
I add a ram section on flash_placement.xml ( <ProgramSection alignment...
I am looking for Static analysis tool ( which is in compliance with standards MISRA-C and CERT-C) to be integrated with Segger Embedded studio.
Is there any preferred...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
Hi all:
About with the nrf_desktop example in NCS ,
I would like to modify the CONFIG_BT_HIDS_MAX_CLIENT_COUNT to '2' ,
so I add below command at "app_ZDebugB0.conf...
Can someone tell me the correct cable to connect the two boards together for debugging purposes.
There seems to be two main options, but its not clear:
TC2050-IDC-NL-050...
Hello, I experience some issues with NRF9160 and eSIM card. SIM_1V8 always output 0v and "AT%XSIM?" return "%XSIM: 0". I want to know if there is prior software configuration...
hello all,
I am trying to find the best power efficiency to transferring a pack of data(30 byte each time) from one nrf52 to another nrf52. I have a 80 uA in average power...
Hi all
So i had a working running example on SDK Thread and Zigbee V3.0.0. This flavor used the softdevice s140_nrf52_6.1.1_softdevice.hex I've migrated to the new SDK...
Hey All
I've found thread, dealing with this problem here: https://devzone.nordicsemi.com/f/nordic-q-a/77775/nrf_ble_lesc-nrf_crypto_ecc_key_pair_generate-returned-error...
I try to connect my nrf5340 CoAP server via my border router with CoAP Messages (with the IP address) from a computer. Is that possible? And if so, How?
I made a border...
