When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
As mentioned in title my nrf52810 dk board will only send uart to putty but I want to send it to another device instead. However, it does receive uart messages from the other...
Hi, I'm developing some products and i need my all devices to synchronize within 10ms difference, using UTC Time standard
Here is basic concept that i want to do for my...
Hi there,
We want to compare the power profile of the nRF9160 with a different device, but for this we want to ensure that both devices are transmitting at the exact same...
We're using nRF5 SDK v16.0.0, FreeRTOS, SoftDevice on nRF52832.
We plan on having two applications in flash. We want both applications to be able to access (read/write)...
Hi,
I am working on BLE 5, I have few queries related to connection parameters
1. Can you tell what is the min PDU size does nrf52805 BLE stack supports with LE secured...
I was wondering in Bluetooth mesh, which layer defines the Relay, Proxy, Friend, and the Low Power features for nodes? For example, is it done by the application, Link layer...
Hi there,
I have nrf52833dk and i have implemented the direction finding examples from nrf connect sdk. kindly guide me about antenna hardware setup that i need to do with...
Hi,
Please excuse me if I ask some stupid questions I am new to wesr and have only used git simply over the last few years. These questions stem from trying to get percepio...
Hi,
I'm designing my own algorithm for direction finding and for that i need IQ value as input. In NCS v1.6.0, in the locator exemple for aoa, the IQ value are store in...
hello,
I'm using SPI in NRF52840 with sdk16, In Nordic Dev zone forum I have read that we can configure frequency of SPIM3 up to 32 MHz but in actually as I can see there...
Hi All,
I am trying to make a project for RGB lights using nRF52-DK using NCS.
In these lines of code I am getting the following error -
'DT_N_ALIAS_rgb_pwm_P_ch0_pin...
Hi All,
wondering if anyone else has experienced this. I'm currently developing a program based off of the ble_hids example in SDK17. Currently I'm using the app_timer...
Hi All,
Setup:
SoC: nRF51822
SDK: 11.0.0
Softdevice: S130 2.0.1
I am facing occasional HardFault and It is happening randomly. I need to test device few hours...
Hi Team,
I am trying to perform firmware update of nrf52840DK using MCUBOOT bootloader over UART. I have followed the link: https://devzone.nordicsemi.com/nordic/nrf-connect...
