hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Good morning,
I'm starting to develop an application for the nRF52805 using ble_app_hrs_freertos as a base.
The modification I did are:
Ported from nRF52832 to nRF52805...
Hi,
I am developing a beacon scanner on NORDIC Thingy 52 using Nordic thingy52 SDK, Now I want to add NUS(Nordic UART service) in my code to send data to the client(ESP32...
I have successfully built the Dynamic Multi-protocols network with Thread and BLE, and used Raspberry Pi 3B + as Gateway Now I want to integrate more AI into the system, but...
Hi there!
I have a host microcontroller connected to the nrf91. The host microcontroller will enabling the nrf9160 through the enable line. From the documentation, VDD_GPIO...
Hi.
The Zigbee stack used in the SDKs automatically stores the network data in the Flash. I know it is possible to erase the NVRAM data with ERASE_PERSISTENT_CONFIG to...
I'm having trouble incorporating the FatFs library into my existing project. I've used CMSIS to update sdk_config.h I've added diskio_blkdev.c and ff.c to the project. When...
Hi all,
I am wonder is there any way to broadcast data using asymmetric encryption algo or digital signature? As I want to encrypt my data using a key and other device...
Hi.
I have got an Iphone 12 and installed nRF Connect. I cannot see the MAC address of connected device. That was possible on my old Android phone.
Does anyone know why...
Hi,
I am using nrf9160 to communicate with LIS2DHTR.
I use I2C_2
In file nrf9160dk_nrf9160_common.dts in ncs\v1.4.0\zephyr\boards\arm\nrf9160dk_nrf9160
&i2c2 ...
Hi there,
I'm using MacOS Catalina 10.15.6 and nRF52840-DK (2019.9) for the Sniffer. My PCB is running BLE on nRF52840. The hex file used for the sniffer is sniffer_nrf52840dk_nrf52840_7cc811f...
Is there a Hardware Design Guidelines white paper for the nRF52840? I'm looking for something similar to what is available for the nRF9160. For example, this:
https://infocenter...
when I used simulator in keil5 for NRF51 software debug, there is a problem : *** error 65: access violation at 0xFFFFFFF4 : no 'write' permission. When I used the keil5 command...
Hi,
I am using nrf52840 DK and SDK version 17.0.2. I want to write data into particular address location(application area) of the flash using fstorage. It is writing the...
Hello ,
On NRF52840 DK my logger works fine and I get no problem with printf(). However, on my custom board the program goes into hard fault with the following :
0x4001...
