Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
For nRF9160, configured for GPS plus LTE: What version of nRF Connect SDK supports GPS+LTE in eDRX mode? Also, are there any plans to provide modem support for GPS+LTE...
Hi, I am trying to test the uart exemple on nrf52840 using external debugging as shown in figure but it doesn't function !!!!
are there any modifications that need to be...
nRf Gurus, I need your help! It is very hard for me to understand top level configuration of the soft devices and overall mentality. I am sure it will be very easy and convenient...
I want to create a 1MHz timer using TIMER2.
I try to start the timer with the following settings, but the device probably hangs.
I also use app_timer, is it a problem...
Hello, Not so long ago I asked this question and the solution I was given is still working for the devices I was using. Now I've received a new version of the device in which...
Hello,
I am using nRF52832 DK module(for master), and breakout board(for slaves, 4-slaves).
I have some problem while BLE communication.
First, I am wondering if I can...
Hi,
I'm getting error on connect to cloud server (socket.nouslogic.com:443) with error code is 45 ( EOPNOTSUPP).
Here are detail:
1. Using https_client example on nRF...
Hi,
I am going to use a timer in my code which includes ble_app_uart (using app_timer) and saadc examples. I need this timer to read time during the program.
I know...
what I use project is "ble_thread_dyn_template" , Is there any way to replace the app's UART console with 'BLE' - i.e. instead of receiving 'ot' commands from UART console...
I need to read (and clear) the general purpose retention register. I cant start the Soft Device just yet, so cant use the sd_power_gpregret_get and sd_power_gpregret_clr functions...
Hi there!
I'm back again, with another possibly stupid mistake. I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. I wrote my own mesh...
Hi Dev team,
I am currently using the NCS v1.5.0 and have a Thingy91 v1.4.0 with me. I want to test the FOTA v2 update from the nRF Cloud to the Thingy91.
I tried using...
I am trying to tune my NFC antenna . The antenna is printed on the pcb. The same Laird antenna is used in my pcb. Based on the antenna tuning white paper I am trying to tune...
When I connect my Thingy 91 to my usb port open up nrf Connect and push Sw3 and turn on the board power I do not get any devices to show up under device selection in rf connect...
