hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I'm having a lot of confusion with using TWI on this chip. I have been running example code that I found in this tutorial nRF5 SDK - Tutorial for Beginners Pt 35 B - TWI ...
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-1-ncs-v1-4-0 I follow the link above to create a hello world project, which has failed all the time. Here is the...
SDK16.0.0 + Mesh SDK 4.1.0
Help, we have developed our own board with a Fanstel BT840X module. Some of our boards are asserting ("Softdevice assert: 154516:0") and I am...
Hi Nordic,
I'm using nRF52 DK (PCA10040). I tried to copy and paste the project from this default location:
...\nRF5_SDK_17.0.2_d674dde\example\peripheral\twi_sensor ...
Hi,
I managed to compile and run(?) my first two programs for nrf51 dongle on Keil uVision, however while i think they run I cannot make the debugger work and see what they...
Any suggested APIs to setup BLE transmit power in NCS?
the set_tx_power() in the Zephyr example looks not work with nordic softdevice controller.
https://devzone.nordicsemi...
Hello
I am trying to compile a project for nRF25840 on a custom board. Build is succesfull but i am getting a 9mb ro-data on the output which means i cant flash it to...
Hi,
I am facing a problem in storing a 64 bit value to a variable.
some of the calculations which is resulting such a high values like this 4701924420
when i am trying...
Is there any way to use remote provisioning of nrf5 SDK example pb-remote in nrf Connect SDK?
If the answer is no, is the implementation of this feature in nrf Connect SDK...
I'm trying to test out the boot loader using the blinky sample. However if I add the following to prj.conf:
CONFIG_SECURE_BOOT=y
CONFIG_BOOTLOADER_MCUBOOT=y
I'm getting...
"SES > File > Open nRF Connect SDK Project..." does not seem to include a thread aware script for Zephyr. Is there a provided script for this somewhere? If not is there a...
Hello,
I would like to use a single COMP I/O pin to compare the pin voltage to multiple references during run-time.
To do this, I was planning on initializing the COMP...
With SDK For Mesh v5.0.0 the mesh_stack_power_down() was actually implemented but there is a bug that will disabled the proxy permanently.
For some unknown reason the mesh_stack_power_down...
Trying out the Sensor Model supplied with SDK For Mesh v5.0.0 raise a few concerns.
The way sensor_initialize() is made requires all supported PropertyId helper functions...
Hello For my application (which is based on the ble_thread_dyn_mtd_coap_cli example), I would like to be able to send a file (for an update) using bluetooth. To do this, I...
