Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
after migrating functional project to latest ncs version v1.5.0 I managed to build and flash it to nrf52840 board without problems. However if I enable MCUboot option...
Hi guys,
I want to add the function of multiple slaves to the nrf_desktop routine to support two hosts to connect to the keyboard .This routine is in the ncs1.4.1\v1.4.1...
Hi,
My application is to scan BLE advertising packet.
My application works when the scan_phys is set to BLE_GAP_PHY_1MBPS.
params.active = true; params.interval = NRF_BLE_SCAN_SCAN_INTERVAL;...
I'm specifically interested in the predefined SPIMn - SCK, MOSI, MISO, SO pins for this device, so that I can marry this information into my CPU Schematic Page. Whilst the...
Hello,
In our application, we have an external watchdog IC. We need to test the timing of that chip during our board power-on self-test.
We currently achieve this by setting...
Hello!
Recently we have noticed that some of our devices has been reporting strange fulgurations on their reported battery level. This is a graph over 24 hours:
When...
Hi I am the evaluation board of nRF52832 (TAIYO YUDEN Evaluation Board) EBSHSNZWZ) is used. I want to use P0.09 and P0.10 of nRF52832 as PIN of GPIO(TWI). It was set according...
Hi,
I'm developing a serialization system with nRF52832 and an application chip. My product is a power-sensitive.
The code of ble_connectivity in nRF5 SDK 17 calls nrf_drv_clock_init...
I've run into an issue with FOTA updates. The issue can be described by the following sequence of events:
A device is completely erased and programmed with a binary image...
Hi,
I am working on programming a bootloader on a NRF52840 DK using a different NRF52840 DK. Currently I have them connected via the debugger and have been successful in...
I am trying to port my build from Eclipse (based on the GCC tool chain) to a KEIL uVision build system.
I am using KEIL ARM Compiler version 6.15. Most of the files compile...
I see many similar questions to this, but I want to double check my understanding.
We have the nRF52840 connected to D-/D+ on a USB Type-C connector. We have a standalone...
Hi all!
I'm using an nRF52833, SDK 17.0.2, s140 softdevice 7.2.0. My design uses a Skyworks SKY66112 amplifier.
I have the pa_lna_assist function that I found here on...
I am running the example:
C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10040_uart_debug\arm5_no_packs
Everything seems to be working well except...
