When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello, i'm currently working on my Bachelor Thesis using Makerdiary Board. I recompiled the OpenThread Libraries to get the CLI working on my Board. I need to read out sensors...
Hello,
I'm trying to use UART0 for communications between the nrf52840 and another microcontroller, while also using UARTE1 for debug communications between the nrf52840...
Hi.
I'm trying to combine TWI sensor and BLE app UART examples.
I already tried putting parts of TWI sensor example in the BLE example, but it gave errors on missing...
HI everyone,
I have issue relate to ble_lbs_init(ble_lbs_t * p_lbs, const ble_lbs_init_t * p_lbs_init) function.
issue happened when i call: err_code = sd_ble_uuid_vs_add...
I am new with nRF9160, just bought a nRF9160 DK from overseas, but I use it in China, two questions come up.
1. Is it working with China celluar network?
I tried the Basis...
Hi,
I'm trying to make the softdevice controller work on NuttX RTOS. I followed the SDK example code to reproduce initialization. All calls are returning 0 (no error). However...
Dear Sir,
we're developing a Ble keyboard with 52810. the product needs to detect what kind of operating system and have different behavior therefore. but i don't know how...
As below, BLE Data RX works fine, but TX doesn't. When does this happen?
Currently BLE connect/disconnect and RX is working fine. The power does not turn off due to this...
Hello: I am trying to design a project about a type of sensor powered by high accuracy battery which is using the nRF52832 chip in a custom board. To use the battery energy...
Hi
My requirement is to upgrade the application firmware on the nRF52840-DK from another processor using SPI interface, and I am trying to understand the code to plug-in...
I'm developing a beacon application using the Fanstel BT832AF, which uses the nRF52810 internally. This unit is mounted to a custom board, but before raising a private ticket...
As instructed to post here by We're using Zephyr on at least 4 of our products and have thousands of boards with NRF chips in the pipeline; we're trying to get the consumption...
I'm trying to install nrfutil, but for some reason the installation is unsuccessful.
After installing python and the executing pip install nrfutil, restarting both the shell...
Hello,
when my application runs, from time to time I see the following:
[00:00:29.000,000] <debug> nrf_sdh_ble: BLE event: 0x26. [00:00:29.000,000] <error> app: ERROR...
