There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
The following issue is for NCS version 1.4.0 and 1.4.1 for an nRF52840 DK target.
When CONFIG_BT_AUTO_PHY_UPDATE =y for both a peripheral and central, I see in Wireshark...
Hi,
I am using the following snippet in my application. it is working fine sometimes but the other times it's not coming out of the while loop.
can anybody point out the...
I have been struggling to reduce the current on the Nordic Dongle to the sub 3 uA levels that the specs suggest I should be able to achieve.
I am stuck at achieving a 9...
i am trying to determine the current consumption of the nRF9160 when in sleep mode but running LPUART and TWIS.
I see that the Sleep mode (MCU IDLE, MODEM off, RTC on) shows...
Hi all, i want to use CMSIS DSP library for vector/matrix computation.
In NRF connect SDK, there is a "nRF CMSIS DSP examples solution" in the dashboard, however it fails...
Hello,
I have an external flash w25n01gv, I am using this simple spi loopback example to test the spi functionality of nrf9160. I want to read the jedec id of my device...
Does doing DFU again and again on same controller can cause misbehavior of code? I am using BLE + UART + EEPROM in my code and sometimes I face the issue with UART event handler...
Hi,
I'm using NRF52840 to connect my mobile.
I'm using whitelist, following the example. It used to work perfectly for about 1 year.
However - in the last couple...
After starting the program, I do the first calibration and read the data 30 times. The standard deviation is between 2.0 and 2.3. Perform 30 "Calibration -> Read Data" each...
Hi,
Greetings of the day!
I used nRF Connect for desktop to program the nRF52840 device. But I can't lock the program and protect the device using this utility. I installed...
Hi,
I tried controlling the LEDs connected to P0.0, P0.7 & P0.11 by using
nrf_gpio_cfg_output(); nrf_gpio_pin_set();
nrf_gpio_pin_clear();
& ble_app_blinky example...
Hello,
My project application demands exchange the data from PC application(custom application developed by us) which is act as a server to the controller which is act as...
I am trying to compile firmware with GCC in ubuntu. The GNU directory is in C:\Program Files (x86)\GNU Tools ARM Embedded\4.9 2015q3. I changed Makefile.posix to m ake sure...
I have a sensor which I'm grabbing FIFO data from every 14msec, ~240bytes. I send these FIFO grabs as soon as they arrive.
My connection parameters:
Connection Interval...
Hello,
I am tested multi-channel BLE peripheral connections. (ble_app_uart example with saadc example.)
When I am testing 2-channel, it works well.
However, when I am...
