Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hello,
I'd like to detect a power failure and keep the nRF52840 alive using for example a super capacitor.
From the hardware side, is it ok to just feed the nRF52840 through...
I am a newbie for BLE MESH. Trying to migrate the existing product which based on self-defined GATT service to BLE MESH network, and got confused.
Current scenerio, the...
Hi.
I am using nRF52840 as a USB mass storage device with SD card. I came across the docs stating that the total number of BULK endpoints available are 14 (7 IN, 7 OUT)...
I have a working code to get FatFs running with SD card over SPI0 interface on a nRF52840 DK. I wanted to know if it is possible to add another SD card with FatFs on SPI2...
Hi,
With the S132 SoftDevice running, is there a way I can ask it to temporarily pause interrupts for a small segment of time so that I can execute extremely time critical...
Hi, The DFU process is working correctly and I've tried downgrading the app version which throws the expected error, so it is stored someplace Accessing via the recommended...
Please tell me everyone's knowledge!
I've seen discussions on smartphones that support "LE Coded PHY", but I'm looking for a tablet size.
Is there any smartphone with...
I'm trying to get my nrf9160 DK to communicate with an i2c device so I setup a project to enable the i2c module and use TWIM to send i2c data. But then I run it and it only...
Hi,
I am using nRF52832 S132 SDK15.2
I am developing an application where the development kit which i am programming is a peripheral.
i want this to connect to specific...
Hey All,
I'm running the LTE Link Monitor on nRF Connect 3.3.3. I'm connecting to my custom nR9160 Feather via the built in USB-to-Serial. I'm able to open the serial port...
I tried to drive MAX30003 to get ECG signals through nrf52832.
I use an analog signal instrument to give the standard ECG signals. Now,the nrf's SPI timing sequence is right...
Hello,
The BLE peripheral I'm developing does not have any specific required connection parameters. I understand that the central ultimately controls the selection of parameters...
Dear
I modify the example of PCA10056 mesh light-server for PCA10059 and it works after I program PCA10059 by nRF Connect –programmer go through USB interface. But there...
Hello,
What is the PPM of LFRC?
In our case, the device will remain in low power mode (System ON, wake up from RTC). The device will wake up at every one hour. Which...
Hello Nordic,
nRF52840, SDK16.0, Softdevice 7.0.1.
I'm using LFCLK to generate an accurate tick for device time keeping (with Prescaler=255, Freq=128Hz, Tick=7.8125ms...
