Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
To the kind attention of Nordic support team,
we are doing ble bonding using passkeys.
We noticed that when starting the passkey phase, a ble connection event is generated...
I am not able to run commands with nrfjprog using the J-link Segger device
e.g. nrfjprog --family nrf52
I can do it only with the Keil or Segger UI environment
How can...
hello
right now i am sending 100 plus data per second i want to print millisecond at each data how can i acheive this is there any program in nordic or github i can use...
Hello
I am working on SDK v17, using nRF52832 (MDBT42Q) and MPU6050 sensor. I tried TWI_SCANNER because I thought there was a problem getting the value of MPU6050.
However...
I am reading a thermistor voltage divider from Vdd using the SAADC with a reference voltage of Vdd/4 and gain of 1/4. I thought that this would track Vdd so I wouldn't need...
Hi, the provisioning works and after that the dk is capable to get mesh messages but oddly enough a restart brokes this feature.
The error message is:
0x0c means BT_HCI_ERR_CMD_DISALLOWED...
Trying to install nrfutil on a system with Python 3.9 but it only installs the old version 5.2.0 which is broken on Python 3. This is the last version before the version check...
I use the internal LFCLOCK to drive my application. Sometimes, I need a more accurate clock to do time measurement. At startup, I can start the external crystal oscillator...
Hi,
I am trying to get Secure UART Bootloader to work and followed the steps mentioned here .
I generated the Keys and updated the dfu_public_key.c file in the project...
Hello,
I'm planning serial wire flash writing from custom board gpio to nRF52840 serial wire.
nRF52840 SWDIO/SWCLK/NRST are connected to a custom board GPIOs.
Is there...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We built 2 configurations for...
I’m using nRF52810 in my design and for BLE communication I want to use Data Length Extension (DLE). Currently I’m using SDK v 15.2.0 , S112 and since DLE cannot take place...
Hi,
I have a very strange issue on my nRF5 development kits and dongles. Whenever I load the softdevice and firmware to the DKs or dongles. After sometime, the USB connection...
when I use central and Peripheral all concerned, Eight Peripheral connected to the central 。when I'll connect my phone to the central Peripheral . Device Error
Here's the...
Hello,
I am using a nrf52 DK in an educational context.
For this reason, I am not using the SDK, but implement basic features on a lower level.
I used the implementation...
