Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
I want to implement a BLE composite device with BLE UART and BLE HID, and both services can work at the same time.
Hello! I want to make a Bluetooth game controller, and...
Dear Nordic Experts.
We designed a device based on the nRF54LS05B module.
We are writing a production test program and using nRF54LS05-DK Rev 0.3.1 for verification. ...
We are using monitor mode on the nRF7002 to receive packets in promiscuous mode. We are on NCS 2.9.1. The Wi-Fi packets we receive have the follow header (struct copied from...
The nRF Thread Topology Monitor is a very useful bit of software. It would be very nice to see it updated, or perhaps even made a first-class member of the nRF Connect for...
Can you pls send recommendation document for the exact foot print to be used for nRF54LM20A-PAAA CSP98 BGA?
I have found reference foot print BGA98N35P10X10_385X367X68.dra...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
Hi,
With the latest SDK v 14.2 is it possible to do OTA updates to nRF52 from OSX/Windows/Linux without the use of additional DK? I understand that for iOS and Android...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
Hello, I want to use ble dfu on nordic. But most examples work with Adroid App, and I need nRFxx transmit dfu to another nordic. Can you tell me if vag has ready-made examples...
Hi,
I need to output a continuous 16 MHz clock on a GPIO pin on the nRF54L15.
I first looked at the GRTC clock output, but since the fast clock is divided by (CLKFASTDIV...
Hi, I am developing a program for the nRF54L15 with the DFU bootloader enabled. I would like to reduce the startup current.
I am using SDK 3.2.4.
The `sysbuild.conf` settings...
