When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
we are using both system on and system off power mode in one of our application.
Sytem on : wakeup through RTC for an every 60 seconds once / GPIO.
System Off :...
Using nrf_mesh_sdk_4.0 and ble_sdk_16.0:
1.I want to load light_switch_server code on nrf_dongle.
2.And then take data from r-pi through usb of dongle and publish it over...
We have been using the nrf9160 successfully for several month. I'm currently upgrading our products to use the new modem firmware (1.2.0) and, together with that, to the most...
Dear All, I wonder if there is a way to empty a work-queue that has work items pending. Is there a way to empty the whole queue or is there a way to remove individual tasks...
hello Nordic
i added a watch dog to my code
i try to create an error by putting a breakpoint in the code (though i actually didn't start the ble scan which usually...
Is there an analog to the `BleManagerCallbacks.onLinkLossOccurred` method where I can receive a notification of when a central re-connects to its peripheral?
Are there any example code or API available in SDK of nRF52833 for AoA and AoD which can be use for direction finding ? i have read the white paper from Nordic semiconductor...
Hi guys !
I am working on SDK 15.2 and I have created a custom service thanks to this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
...
Hi The nrf9160 product spec 1.2 states that the number of times a 32 bit word can be written is 2. I have used the nrf52840 a lot and has a similar restriction but on seeking...
Hi,
In my project, there is a lockup issue like the title. (SDK 15.3.0_59ac345)
When I try to erase flash, some data (uart command for the device)comes up through the...
Hello,
The last ticket referencing this topic is 2 years old. I thought I would ask this question since we now have NCS.
Application is a Gateway that will support Zigbee...
I am trying to fun the LTE Sensor Gateway on the Thingy:91.
The boards are missing from zephyr so I copied nrf52840_pca20035 and nrf9160_pca20035 from ncs\nrf\boards\arm...
Dear all,
I'd first like to apologize if my questions seem dumb. I'm a student in mechanical engineering and only just started getting accustomed to microcontrollers and...
Hello,
I just installed SDK and Embedded studio.
And when I try to rebuild example, error occurs.
Below is my setup information.
- SDK: nRF5 SDK 16.0.0
- Example...
