Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
I am trying eddystone example from SDK 15, its working fine but once I press the button to enable connecting and function nrf_ble_es_on_start_connectable_advertising(); is...
I want to use REG0 to supply 1.8v to external 4.7k pull-ups including when the system is off. Looking at the product specification REG0 can supply 1mA while in system off...
I have updated my repos to the latest commits on master for zephyr, mcuboot, nrf, and nrfxlib. I ran `
pip3 install -r scripts\requirements.txt
and I can open the asset_tracker...
hi, I'm working with NRF52832, DFU service is configured as secured. my question is : i'm trying to change dfu char a ct e ristic property to "ind i cation" by writing to...
Hello
I would like to test if provisioning over GATT Bearer still works with our application. Firstly I thought of using the serial example together with the PyACI, but...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
I use the QSPI(SDK15.2) of NRF52840 to read and write FLASH. Every time I open QSPI function, QSPI is closed after writing flash, but after close QSPI, there will be occasional...
Hi,
I want to capture data from TWI ADXL345 and send them by ble_nus_data_send() to mobile. Timing of data sending is done by application timer. My problem is that when...
Hi,
I tried to merge ble_app_multilink_central and ble_app_uart_c.
But, when I run the project It errors like below
I thougt the problem is the address of RAM_START...
