hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi, had to modify this file
SDK nRF5_SDK_15.3.0_59ac345 in file apply_old_config.h
line 818
(SPI_ENABLED && (NRFX_SPIM0_ENABLED || NRFX_SPIM1_ENABLED || NRFX_SPIM2_ENABLED...
I've been learning to use the PWM.
This should set the PWM up for a period of around 250ms
After the period is over I expect to clear pin 23.
I find that its cleared...
Hi All,
In nRF52 SDK 15.3.0 , example ble_app_uart in peripheral mode, i have changed the TX characteristics which is initially of type (notify) to type (read ). I am able...
Hi community, I have a problem establishing a connection with more than one device in the MQTT client example (MQTT/6LoWPAN/BLE). I'm using:
SDK v15.3.0 (also nRF5 SDK...
Hi,
I'm trying to connect my nRF52840 SoC to nRFgo Studio on my Windows 7 Laptop using the usb connection on the nRF52840, unable to see any data about the connected board...
Hello everyone,
I need transfer large data 12KB array send central to peripheral using nrf52832. I try this examples in central (ble_app_uart_c) and peripheral (ble_app_uart...
Hi,
I am using nrf52840 with custom board, sdk 15 and and softdevice 6.0.0. I modified saadc example to sample SAADC value once and stop it in saadc_callback. Everything...
I would like to know, what is the correct workflow with Alarms ZCL cluster?
There are no examples with it in SDK (at least, as I have seen). The documentation on this subject...
Hello,
We have started to design a project and we would like to use the Nrf52840 as border router with a linux terminal. The link would be a serial over USB. So the NRF52840...
Hi,
I'm trying to create with the S132 SD on the nRF52832 an application, that will provide 3 different kind of sensors. My goal is, that these sensors will appear as an...
Hi there, I could not find any documentation about the meaning of the version numbers, when creating bootloader settings:
nrfutil settings generate --family NRF52840 --application...
Hi
I am working on Eddystone in nRF52832. Its working fine when using power supply.Then I used Lithium battery as VDD. then it not working properly, only working in connectable...
Hi,
I was wondering what is the recommended GPS circuit would be for an always outdoor device with a large patch antenna, without the need for an amplifier. Would the following...
Hi all,
I have my custom nRF52832 board, I use SDK12.3.0 with SD132.
I'm currently trying to add BLE advertising to my firmware. To achieve that I'm copying parts of...
Hi,
I am performing the following test:
https://devzone.nordicsemi.com/nordic/b/blog/posts/testing-long-range-coded-phy-with-nordic-solution-it-simply-works-922075585...
