I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
I'm trying to use AAR peripheral, but I don't know the structure of output DMA job list, as it's not defined in the datasheet. I was trying to use one job pointing to flat...
Hi,
I'm transmitting using the nRF24L01P and using the nRF52810 as the receiver, 5 byte address.
We send a 2 byte packet usually 0x00, 0x00 until data is ready. If I set...
BT_DRV_RX_STACK_SIZE is too small and can't be configured. It needs to be more than 512 bytes in released versions of Zephyr, or 640 bytes, on the main branch. Note: I'm using...
Good morning everyone,
I am going crazy to solve this problem, but I hope we can figure it out with some help.
I am working on a prototype for which we need to use a...
The documentation for the Maximum Performance sample mysteriously states that the sample is not supported on the 5340 with no explanation as to why. As I am getting spurious...
Dear support,
I am using this board: https://www.nologo.tech/en/product/otherboard/NRF52840.html#%E5%BC%95%E8%84%9A%E5%9B%BE . I am trying to use any analog input to eventually...
nRF Connect for VS Code v2024.12.55 showed up yesterday and it seems to be broken for me; the "build", "flash", debug" buttons are not available to me, I am stuck with "Pristine...
Hello,
I fear that my toolchain and environment is seriously confused.
When i use the vs code extension sdk to install a toolchain or sdk i get the following message ...
I Have been trying to interface mpu6050 with nrf5340 DK .
f ( NOT "${ret}" STREQUAL "0" )
message (FATAL_ERROR "command failed with return code: ${ret}" )
endif (...
Hi,
I'd like to know what is the cause of the stall in
sym_E5Q6O4GY4KO3GMW7WJYXLZKHO7ZGDWLU4ZPAKWA() at 0xa55a
when calling sdc_hci_cmd_le_set_adv_enable ?
Here is...
I am currently considering the use of an external Flash IC for a Matter device.
I have two questions and would appreciate your help:
1. Is the MX25R6435FZNIL0, which is...
Hello,
according the datasheet the nRF52832 has an gain error of 0.02%/ ◦C and E_G1 of -3 ... +4%. This is too high for our requirements. Is there a way to improve this...
Hello DevZone,
I'm developing a HomeKit project for the customer. They require 2 BLE advertising in one device. One advertising is for HomeKit over BLE, and the other one...
i want to switch between two code... the code is simple led blinking i am trying for the testing purpose...in my code 1 led1 is blinking 500 ms of delay and in my code 2 led2...
So from my understanding from the zephyr documentation, if I want to use 7 bit I2C addressing, don't set I2C_ADDR_10_BITS. I am wondering how I can make sure this macro is...
