When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating CDC ACM...
I'm using version 2.0.0 of the Android version of the device manager app. When I select my device from the list to do a DFU it immediately closes the app. Normally it would...
sometimes the param update will fail and sometimes will not. May I know what the reason is and how to solve this issue?
error case;
normal case:
my prj.conf...
Below are power consumption measurements of a DUT being booted with the same PPK2 in SMU mode with various software versions. The only variable being changed is the PPK2 software...
Hello all,
I want to use nrf52840dongle to receive notifications from other BLE board.
I have tested with nRF Connect for Desktop Bluetooth Low Energy successfully.
...
Hello,
I'm using nRF5340 audio application with nRF Connect SDK v2.7.0 on nrf5340 Audio DK.
I didn't change anything in the sample code but only modifying the NRF5340_AUDIO_TRANSPORT_MODE...
Hi there,
I generated the DAC, PAI, and PAA certificates using the chip-tool and merged them into my firmware as factory data. Additionally, I generated the Certificate...
conducted an ADC experiment using the nRF5 DK (PCA10056).
The power supply for the nRF5 was provided via USB.
Based on the SAADC sample, I coded the following:
...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
Hello,
I want to operate a rather complex spi sensor with the nrf5340. To do that, I wanted to first establish spi communication. I started by creating a hello world example...
My name is Cedric, responsible for Workplace Management at ´my company, which also includes application management. We try to install all of our apps centrally via Intune...
I am using the LPUART and running into an issue when the UART is disabled. The LPUART doesn't notify the user callback that the buffer can be released. In my case, I am using...
I developed a project using nRF Connect 2.6.1 in VSCode. I created a custom board for the development board I was using (the SparkFun Pro nRF52840 Mini - Bluetooth Development...
