Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
We are using STM32 board as a HOST controller and NRF9160 as cellular modem. On the STM32 board PPP client is running over serial interface.
We need PPP server support...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
I have a nRF9160 custom board. I am using 2 UARTs (UART0 and UART2). I need to have an RX interrupt on both UARTs. I have identical setups and configuration and code. The...
We are using PC-BLE-DRIVER-JS for our central and zephyr in our peripheral (833). The central bonded with the peripheral only when the id (IRK) param in our central is set...
Hi all!
Hopefully this doesn't come off as too much of an ignorant question, but I'm having a hard time understanding the pinout of the Thingy 91 since I can't map where...
I´m trying to design a compact circuit for the NRF91, since i have limited space i´m planning to do a board stackup with the antenna board on top. Right now my board is 50mm...
I am working on an application where I am using 3 SAADC channels all with the same reference pin.
Upon startup, I will call app_sensor_init() to initialize my SAADC, timer...
The Commissioning and Characterization note for the nRF700x series ( https://infocenter.nordicsemi.com/pdf/nan_043.pdf ) says in section 2.1.2
However I have been unable...
Hi! We are considering moving from nRF9160 to nRF9161 on our custom board.
We are currently running modem FW 1.3.1 and nRF Connect SDK 2.0.2 on the 9160. However, we find...
Hello,
I am looking to conduct a test to simulate a Zigbee device using nrf52840 in the Zigbee:shell sample. This involves modifying the manufacturer ID and model ID. If...
I need a clarification about the update of gpiote driver. I've passed from the NCS 2.5.1 to the 2.6.1 and now I have issues in the configuration of my ppi infrastructure....
Hi,
I have a peripheral which is sending data to a central via the NUS service. Everything works as expected until the central is removed (e.g. power failure)
The problem...
Hi, basically I want to expose my firmware's version through the GATT DIS (Device Information Service) to client applications.
I have gone through:
the VERSION file...
The link provided as part of the webinar to download the PPT is not working, So could you please with PPT
Following is the webinar link
https://www.youtube.com/watch...
I develop using Apple M3 paired with VS Code with nrf extension. The development board I use is NRF52840DK. When using JLink firmware with version number JLink_V796b, the...
