Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
When configuring the watchdog to pause in sleep mode, is it automatically fed after a wakeup from power_manage()?
Is the feed required in this loop, or can I leave it...
We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Hi,
I'm working on an app that currently uses Thingy91 as a main board (nRF9160 as main MCU for LTE nRF Cloud Connectivity and nRF52840 for BLE connectivity via HCI UART...
Hi,
I have a PCA10040 and use nRF5_SDK_17.1.0_ddde560.
I build this example project in Segger Embedded Etudio and it works fine and I can load elf file and debug etc...
Hi,
I would like to seek a guidance with proper usage of DS3231 as LFXO with nRF5340.
HW:
Custom board, DS3231 32kHz output connected to nRF's X1 with pull-up resistor...
Hi Team,
Facing below issue related to MPSL.
** Booting nRF Connect SDK v3.3.0-ba167d9f3db4 *** *** Using Zephyr OS v4.3.99-fd9204a02d52 *** [00:02:14.519,667] <inf> app...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Hi Nordic Team,
I'm developing a quarter wave PCB antenna, based on Nordic's white paper on the topic, for the nRF54L15.
I've two concerns on how features around the...
Dear Nordic Team
our customer are making the batterie profile by using NPM-FG ， by profile logging , it was all fine by testing under low temperature and room temperature...
Hi, I'm current evaluating the NPM1300. I've made a prototype board, using nrf54l15 and npm1300. I did not know that i need the npm1300 EK to do battery profile. Due to being...
Hi Team,
Currently I am working with nRF54LM20 DK. And tried to import and use echo bot example from SDK. And modified the overlay file as per the UART pin changes required...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
I've just spent about 4 hours trying to figure out why a particular build was failing (on nrf9151dk).
Examing the cryptic errors finally revealed that the TFM partition...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
