Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
These two func:"softdevice_ble_evt_handler_set "
and "softdevice_sys_evt_handler_set" suggests that there are two categories/sets of events grouped into system & BLE.
...
I'm a user of nRF52 DK with S132.
I want to modify the event handler in the example application code such as ble_uart_c.
Where can i find the full list and description of...
Hello
Can I use the LORAWAN module with NRF52833? if yes, is the LORA gateway also required to send the data to the cloud, or can it be done directly without a gateway?...
TX :52840
Software version：nRF5_SDK_16.0.0_98a08e2 hardware version：
RX:52820
Software version：nRF5_SDK_17.1.0_ddde560
My test method: send 60 bytes of data through...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
I am experiencing a strange behavior with SES 6.32, using GCC and I wonder if I should choose a different compiler.
COMPILING THIS PART OF CODE (I added line numbers for...
I want to add wifi connectivity to asset_tracker. It is required that MODEM is turned off. The program flow need to change so that instead of Modem, wifi Module is tried first...
Hello,
I am trying to read a 32-bit value over BLE but the value displays as 8-bit on nRF Connect. In my code I am sending it as an int32. Why does nRF Connect only show...
Hi There,
I have almost done the project, I used nrf52832 as central(master) and nrf52810 as peripheral(slave).
i use the blinky example and everything working fine. I...
Hello,
I am using nRF52840 and I currently am working on a application where mostly I am using central functionality (BLE connection and exchange the data) along with cellular...
I'm willing to use the 5 claused licensed code for the parts that only work with nordic hardware, but the partition manager isn't actually necessary. Is there some way to...
Hi,
I am trying to migrate a moderaely complicated nrf5340 app from sdk 1.9.1 to sdk 2.0 and having a few issues with getting the right crypto configuration. Original...
