Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I'm attempting to add support for a custom ili9341 display to a project running on a the uBlox Nora dev kit. I'm currently using VS Code with nRF Connect SDK1.9.1. My question...
tried the proximity example to check pairing/auto-repairing using PCA10040 board. currently having not auto repaing after we power OFF/ON the device.
we are planning to...
Hi,
I encountered an error when I turned on NRF_LOG_BACKEND_RTT_ENABLED in a project:
"...section '.log_backends' will not fit in region ‘UNPLACED_SECTIONS’."
"region...
Hi All!
I am using nrf21540 along with nrf52833/20. My question is can it be possible to use nrf5 SDK instead of NCS? I have developed the application using nrf5 SDK and...
Dear nordic team,
we are successfully communicating our old nRF2401 shockburst design to a nRF5340 board; except for the CRC.
The challenge: the nRF2401 shockburst allowed...
Hello,
In function such as i2c_write and i2c_read does Zephyr check to make sure the device is not a NULL pointer? If not how would it react if it were passed one?
...
Hi,
I tried to run the "matter" light_bulb example from nrfconnect versions 2.0.0, 1.9.1 2.0.99, but failed to
to see blinking LEDs. I suspect this may have something...
Hello dear Nordic. I am reading your documentation and stuck on the following issue:
According to the SEQ[1].CNT register there are 3 pulses with different duty cycle...
Hello there,
The same code works reliably on dev kit but not on my customized hardware. By cutting the 32k external crystal jumper on the dev kit, the same failure can...
Hi,
I am working on nRF52840 dongle.
i am facing a issue with programming. before it i was trying to do it with arduino. i don't know its bootloader gets disturbed....
I build the asset_tracker with custom code added to it and working well. The build time messages are shown in the attached text file. There e %of Flash used in show thrice...
HI,
I'm trying to configure the MCUboot / Netboot with an external QSPI flash. I can do it for the APP core with MCUboot, however I get lost how it work with the NET core...
Hi Nordic team
We plan to develop a stereo bluetooth loudspeaker, that can be connected from any smartphone to stream audio.
The prefered audio output would be PWM since...
I am working on firmware for a custom board with an nRF9160. Specifically, I'm trying to get FOTA updates working, using the provided library functions for it. I had no issues...
