Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I downloaded the project for PCA10040 with HID Mouse in ...\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs . From Iphone and computer, I could...
Hello,
in my project i want to use watch dog timer in ble_app_uart_pca10040_s132 but am getting error as shown in image1, even after including driver files and paths
...
hello,
I'm trying to use RSSI Viewer for my custom board - problem is I need to change UART pin.
How do I make my own FW/binary for RSSI viewer?
My custom board uses...
Hello,
I'm very unexperienced with low-level programming, so I apologize is some of my questions make little sense.
We have this board that sends telemetry data using...
Dear Support,
I updated the nRF Connect for Desktop's Programmer to v3.0.0 and noticed that it is no longer possible to write a file to a nRF9160 using a Segger jLink without...
I am currently programming an evaluation board to get to know BLE better. Currently I am using the nrf52811 on a custom board.
So far I used an example from nordic to create...
Probably there is already some solution here in the forum, but I couldnt find a fitting one.
My problem: I have custom code on my nRF52840 DK, which is used as an aggregator...
Hi,
I am running a multirole device based on the 'central_and_peripheral_hr' samples of nRF Connect SDK v1.8.0. The device holds a connection as peripheral and it is scanning...
Hi Sir/Miss,
I use nRF52832, softdevice 132 and SDK 17.1.0 to develop.
And, I want to use GPIO to wake up from system off.
We use external pull up resistor in wake up...
I'm testing with the new rev of the nRF52832 (build code QFAAGB on the package), and I'm not able to observe behavior that makes sense to me per the updated product spec....
Currently working on a nrf52dk_nrf52832 kit. I have a SPI flash that I am trying to use - I am using the nrf SDK ncs v1.9.1.
I know I can use any of the GPIO pins for SPI...
Hello
I have a mesh node that needs to broadcast a custom BLE packet
To start advertising I call bt_le_adv_start and it works as expected.
I'm curious about the error...
Hello,
I'm in nRF Connect SDK 1.5 and I have to change the baudrate of UART1 at runtime. I have to use Zephyr UART Functions. I have tried the function uart_configure()...
