hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I'm trying to publish values using a predefined message context.
This works fine when using bt_mesh_onoff_srv_pub or bt_mesh_lvl_srv_pub, but I get a crash...
Hej!
Do you have a reference design for nRF52840 and nRF21540, how to connect the ANT signal (nRF52840) to TRX (nRF21540)?
Is it enough to only use a DC block, C1=1.0pF...
Dear All
I used nRF24L01 antennas with external antenna for data reception and transmission at different speeds (256KBPS, 1MBPS and 2MBPS) for a while everything worked...
Hi
I'm having trouble when trying to connect nRF 52 DK with BLE app on nRF connect for desktop.
I can select device of my nRF52 DK, but cannot not scan any discovered...
HI Nordic, I've looked through all the documentation and tried a bunch of failed experiments...so I thought i'd ask you. On the nrf52840-DK, I'd like to
Connect the DK...
Hi,
I want to program my nRF52833 has tx. The example is provided for pca 10056 and pca 10040. I know that it's possible to change the configuration to use it on pca 10100...
Hello,
I am creating a BLE Rx/Tx connection between two NRF52840-DK's similar to the Nordic UART Service. With the goal to achieve around a 100/100 KB/s connection. Only...
I have a system that consists of a sensor (nRF52840), hub (nRF5340), and gateway (nRF9160). The high level end goal is to be able to publish a MQTT message from the sensor...
Hi,
I'm looking for AES encryption aes_ctr, nrf_crypto example to try on NRF52811 but, I don't see any example for pca10056e.
Does that mean nrf_crypto is not supported...
I tried to deep dive through the macros, api abstractions and other layers but couldn't figure it out. The closest I got is this:
void debug_uart_print(const char * s) ...
Hi,
I have been evaluating the nRF5340dk for our application purposes and I am currently investigating on how the bluetooth directional finding works.
I happened to...
Hello Devzone Community,
I am continuing my long trek toward single-microamp operation of an nRF9160 based, custom board. On the LTE modem front I am making `AT+CPSMS=`...
Good afternoon.
We have an issue which we'd like to prevent, but suspect it may entail changing the out-of-the-box MCU Boot / SMP BLE code / process.
If we flash our...
Hello, I developed a custom PCB that uses the nRF52810 microchip, and I wrote a firmware that needs to use three RTCs.
The program is supposed to wake up the CPU by an RTC...
Hi there, i have a thingy91 for the electromaker contest. I've flashed the nrf51 bridge firmware using MCUboot. All went well. However, when i try to put in DFU mode the nrf9160...
