Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
I have seen a few tickets with people not getting any CTE data received and program restarting after "Waiting for periodic sync lost..".
Did anyone get it to work...
Hi!
Continue the previous case
I try to run zephyr direction finding rx example direction_finding_connectionless_rx
It seems to me that the external antenna is working...
Hi
I am working as a member of a team owning nrf9160 dk. I want to work remotely with the same hardware they have. but right now I do not have physical access to the hardware...
Hi, I installed VS. The screen shot is shown below. How to open, Build, Compile, RUN and Debug sample applications and custom existing SES projects. May, some one explain...
I am trying to program my nRF51 QFAC, but it tells me to adjust my linker settings.
I am using the SDK 12.3 and the softdevice 130 2.0.1.
However, after I apply the...
MCU : nrf52833
SDK : Ver 17.1.0
SoftDevice : S140
I try to call RTC value to external RTC Module by TWIM in BLE authentication rw request event.
But MCU stop to...
Good afternoon,
I built and flashed the Bluetooth Multiple advertising sets sample in VS Code using the nRF Connect Extension Pack onto my nRF5340-DK and come across an...
I am trying to measure my battery level on my nRF51822 beacon board through the internal ADC.
The chip is just advertising itself every 5 seconds.
The measurement works...
Hello,
I am trying to develop a low-power application based on the direct test mode example. I saw in this blogpost: https://devzone.nordicsemi.com/nordic/nordic-blog...
Hi there,
We are currently developing and testing on the nRF5340. We are using our own OS (not Zephyr).
We measure power on the devkit by connecting the PPK2 as a source...
Good day I am wondering if anyone can help me
For background information.
Network - NB-iot
Firmware - 1.3.1
Software - Serial LTE Modem
Hardware - nrf9160dk
...
Hi,
i wanted to i2c interface of nrf with adc ic 3427. i am trying to interface by refer example of twi_scanner device address get found correctly.
now i am trying to...
On an nRF52840 using SDK 15.3 and FreeRTOS 10
I've got both a PCA10056 dev kit and a custom board. I don't think I've got a hardware issue here but I'm running the usb_msc_pca10056...
Hi guys,
I have developed a custom board using the nRF52840 module and the SDK16.If the peripheral is disconnected from the central, it starts advertising again in normal...
I have a custom nRF52480 board and addded mesh functionality based on the light mesh sample
The app crashes during provisioning from the nRF Mesh app.
Relevant portion...
