Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello, I'm working with the event manager doing a customized Asset Tracking version firmware. The problem is that when I attempt to submit an event with an array with fixed...
Hi,
In my system I have a timer that ticks at 1kHz frequency, collects some data and sends it over BLE via bt_nus_send. It works fine, but in the beginning of the stream...
I want to incoorperate the pc-ble-driver into a product, using the PCA10059 USB-dongle. My design requires me to receive advertising scan responses. I successfully receive...
Hi,
I'm using nRF Connect SDK 1.7.1 with nRF52833dk.
I'd like to implement DFU over UART.
I see a number of examples to achieve this with SDK5, but not with nRF Connect...
Hi,
I would like to know how much noise I have to expect with the SAADC.
I tried the example "saadc_pca10036" and attached the pin P0.02 (AIN0) to a ground pin on the...
Hi,
I have a project with 3 threads running on a nRF9160. I am using nRF Connect SDK v1.8.0. Basically I borrowed the code from "mqtt_simple", "location" and "threads"....
Hi all,
I am working on a project which needs dwm1001 library integration with nrf52 ble code. I am using ble_app_uart code. decawave have provided dwm.o and libdwm.a...
I have an issue compiling the example code from SDK 17.1.0 using Microsoft Visual Studio Code in Windows 10. Using the easiest example possible, after starting a terminal...
Hi Nordic,
I'm able to do dfu without validation after few days of studying documentations and forum.
Here is the settings page i'm flashing:
But i had to disable...
Hello all,
the sensor is selected and so far powered via an external power supply, while the nrf52dk is powered via the USB, however, I am not sure how to properly organize...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
Recently I just found that when clicking the flash option in the vscode, the IDE only builds...
Hi,
I'm using the saadc and I notice that the max value that saadc can convert is 3,3V. If I try to convert an higher value, the result has no sense. For my project, I need...
Currently I am working on a open thread project.
Right now I am facing an issue in which my board/code is getting reset every time after I have done some changes in my previous...
Hello,
Currently In customized PCB board, nRF52832 is connected to both HFCLK(32MHz) and LFCLK(32MHz).
It takes up too much space. So HW engineer asked me to consider...
Hello. I have a device that connects to desktop app through usbuart-to-ble converter and I'm trying to simulate it using nrf52832. I've started from ble_blinky example using...
