Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
I try to install nrfconnectsetup330ia32.exe on my Windows-10 x64 bit computer. The setup program hangs when the progress bar is at about 33%. It just sits there without...
I am currently working on Nrf52840DK board trying to run ble_uart_app. Designed my board and I used BT840 instead of Nrf52840DK . After, code in NRF52840DK is working but...
Using a Thingy!91 (v1.0.0 and v1.4.0, firmware 1.2.3, 1.2.7) I get sometimes (every couple of days) a ENETDOWN when sending data out. Before that ENETDOWN, the device was...
Hello,
I've been working with NRF52840 for a while now. Recently I decided to add extra options to your code so I went to the development kit for a quick test and debugging...
I cannot get the esb ptx sample to compile on NRF52833 device when using VS Code v1.64.2 running windows 10 64bit .
I've installed everything according to videos, and when...
I am developing a nRF52832 based project where I want to position people indoor using an smartband (where the nRF52832 is placed). I was planning to use beacons so I can change...
Hello,
I have a ported a project from Keil (uVision) to Segger Embedded Studio. Everything is compiling, but unfortunately I have a problem with the linker I cannot solve...
Hello,
I am looking for some advices for a personnal project.
I would like to be able to receive all BLE packets ( so all protocols (GATT, SM, LL) and not only GATT) that...
Hi Nordic team,
I have used the nRF5340 BLE Online Power Profiler extensively in the past for things like estimated event energy and estimated battery life. Do you have...
Hello,
I use the nRF52840DK with direct programmed registers for NRF_RADIO peripheral to send and receive 802.15.4 frames. I have also a separate laptop with nRF52840 USB...
Dear all,
We're developing a custom HW with several nRF52832 chips on one board. For convenience we applied third party module instead of building minimum system by ourselves...
Hello,
in our device we use the Timeslot API to share a 802.15.4 based protocol with BLE, softdevice is S140 6.1.1.
Problem: the 802.15.4 protocol misses appr 10% of the...
I'm having issues using the debugger on the nRF9160dk.
Here is the log that is output when I try to program the on-board 9160 with the command, nrfjprog --program <path_to...
