Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello
I have success to load and run the sample, but....
After receiving OK from the AT#SOCKET=1,1,0\r\n command I could not success to AT#XCONNECT="google.cm",80\r\n...
Hi,
I am developing a device that uses a custom nRF52840 module. This module is assembled on a mainboard that contains an ICS-43432.
We are developing the firmware using...
Hi all,
I'm recently working with Nordic devices (more precisely nRF52840), so I'm still learning. I'm working on a project where I have a shared SPI bus with several devices...
sorry i closed the problem by error
Hello, I did my own custom board with an nrf52805 and I'm trying to put a module with different frames, and when I do that my...
Dear DevZone Team
The nRF9160 datasheet stipulates output power as +23 dBm. I read this as conducted output power at ANT pin and not EIRP which to my knowledge implies the...
Hi Nordic，
My customer is doing the BQB certification, and they come up with a problem.
When they test the 2402MHz channel, they found that power of 2400MHz is greater...
Hi
I am using NRF52840 SDK17.1 with ble_app_uart project to be a server role. Some behavior as below:
1. Use phone's app could communicate it successfully. Write and notify...
Hi everyone,
I am using nRF52832 DK to transmit data to another development kit. During advertising, I measure the current with PPK II and see that the DK draws a static...
For he IO pins you have identifed for LF use, is this related to the correct operation of BT (as in these IO would induce noise and affect the BT operation) ?
Hi,
We developed a product based on the eddstone example, I have a question about the minimum Tx interval,
Minimum interval = number of configured slots * APP_CONFIG_ADV_FRAME_SPACING_MS_MIN...
Hi,
I need to record audio using ICS43434 and then process the recorded audio with nrf5340. Then I need to write the file to the flash memory. I need to know is it possible...
Hi,
I have noticed some strange issues with the modem part while developing. Sometimes the Modem is not connecting to network anymore. Our code has a loop that uses
lte_lc_offline...
Hello, All,
I want to use the GPS positioning function of the nRF9160, currently using the "nrf/samples/nrf9160/gnss" sample for testing, the type used is GNSS_SAMPLE_ASSISTANCE_NONE...
Hi.
Hope someone could help me on how to scan and parse the Manufacturer Specific Data that comes after the Company ID. I am using zephyr with nRF52840.
Thanks!
