Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I am using nrfutil version 5.2.0 on a Mac Pro M1, running Mac OS Monterey 12.1. I get the following error when I try to generate a private key
------
Us-MacBook-Pro...
I just bought an actinius icarus board, and am trying to connect to it on linux (or windows),
The problem is that when I plug in the board in the usb, it will only appear...
Hi
1、Becuse of customer's PC administrator has been implanted managed software in the engineer's computer，So the m anaged software may limit some processes in the computer...
Hi,
After upgrade from nRF Connect SDK 1.4.1 to SDK 1.7.1 we have seen an increase of the current consumption with about 100uA.
Before with SDK 1.4.1 the idle current...
The non-standard function mlme_rx_enable declared in the header mac_mlme_rx_enable.h does not seem to be defined in 802_15_4_lib_gcc.a.
The compilers throws an error: undefined...
Hi all,
I'm trying to put the system into the SYSOFF mode when the device detects an external charger. HW-wise it's implemented by the charge controller pulling a GPIO HIGH...
Hello,
Let me just briefly state that I have referred to required documentation and also executed spi_transceive_async() test, at zephyr\tests\drivers\spi\spi_loopback...
Hi
I want to use nrf52840 to develop a central like figure below，the central can connect and communicate with all kinds of peripheral. Is there a reference example？
Hello,
NCS1.8.0 Windows10 X64;
spi_loopback test,default code default pins;it is ok.
when i change the SPI_1 pins ，
Failed to achieve the effect, still used the original...
When setting up a pin to toggle on the RTC's TICK event through the PPI and constantly reading the RTC's COUNTER on the nRF52832, my team observed frequent glitches on the...
Hi All!
I am using the cloud client example. The development board is nrf9160. This example works well and sends the message to nrf cloud on button press. Is it possible...
I'm using the Nordic Python libraries to receive the BLE data. I can send the data from our board with the nRF52840 chip on it. If I send the data to my Android phone with...
Hi.
In order to save battery in an "advertising only" peripheral, would it be possible for this module to remain in sleep status and start advertising (for a preset period...
