Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
We have a custom PCB with external crystal for HFCLK. Can you tell whether the external crystal is used by default for HFCLK or it has to be selected in the HFCLKSTAT...
I am using timer 3 as a counter for my capacitor discharge time. Currently, the value of is always problematic because it shows with too many deviation values sometimes...
Hello,
Is there any user manual to the nRF Connect for Android? I guess it is quite simple tool, but I am complete beginner in the BLE and would appreciate some description...
Hello All,
Currently we have a nRF52832 firmware .hex file for mass production.
And we use "nrf connect - programmer" to firmware programming without any problem.
...
Hi!
I'm updating to SDK v1.7.1 and I am looking at the changes in LwM2M Carrier Library v0.20.1. I was previously using LwM2M Carrier LIbrary v0.10.2
The big change is...
Hello,
I'm trying to install circuitpython onto an nrf52833 dk board, and am running into a fair amount of trouble.
Wondering if anyone can provide a guide on the explicit...
Hello,
I am trying to port the 51822 project to 52833. I am testing the port to 52832 temporarily.
The 51822 project is a commercial product.
SDK – 17.1.0 SD-S132, PCA10040...
Hi ,
I check the datatsheet "nRF21540_PS_v1.0.pdf" but I confuse on page 22 "TX_Gain initialized with POUTA_PROD (20 dBm +/- 0.5 dB)".
Which one is correct??
1: Tx gain...
I’m trying to use the Power Profiler app v3.2.0 under nRFConnect for Desktop v3.9.1 with a PPK 1 attached to an nRF52 DK board (containing the 52832 processor), but am having...
Hello, i'm having trouble with my new Board Nrf5340, i cannot detect the board to my PC.
I connected with micro USB and when i'm going to the device manager, i'm not seeing...
Problem:
Tried to compile (west build --board nr52dk_nr52832) the C:\nRF\v1.7.1\nrf\samples\peripheral\lpuart project but it failed to compile. I discovered this after updating...
Hello All,
I am new to use Segger Embedded Studio and NINA-B406 module. I have installed Segger Embedded Studio V5.50d and EVK of NINA-B406 module having nrf52833 SoC. ...
Hello All,
I have taken usbd_ble_uart_freertos example and modified it for USB MIDI example (taken from Github) for nRF5 SDK and modified it to use nRF52833 SoC.
I am...
