Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi Forum,
i've ran into a problem with configure the nrf24l01. I've disabled all ShockBurst functionality (EN_AA = 0). When putting TX Payload into the Fifo the TX_EMPTY...
Hi~
We are going to use the MAC address and UUID as what we have.
I am trying to save the MAC address and UUID through UART, so I don't know what to do.
Currently the...
Hello,
I am trying to make a code running the Ble stack adn the FreeRtos one, i started from the project ble_app_hrs_freertos_pca10040_s132, i've just removed some things...
Hi.
Newbie stuck at installing IDE.
Trying to follow the automatic installation developer.nordicsemi.com/.../gs_assistant.html
Installed nRF Connect for Desktop v3.8...
Hi,
we have nrf52933 custom hardware.
we are flashing application through j-link.
but after every flashing , I need to hard reset the board in order to run the function...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Set transmission parameters 100mS interval and 4dBm transmission power...
I have nrf52840 dongle will like to treat it as central. (like gateway) And sensor node is unknow ble, and adress type is Resolvable Private Address. If know the characteristics...
Using the « nrf_modem_at_cmd_async » function triggered an HARD_FAULT error if it is the first function used in the code before another function of the AT interface of the...
Hello everyone I would like to produce my own custom board based on the NRF52840, but the quartz used in the Dk is sell by package of 3000 pcs so I decided to change and use...
I have troubles with the bluetooth examples on the nRF5340. Examples without bluetooth works fine. (blinky of hello world). I allready found out that the code is waiting on...
Hi,
we're using a library which is written in C++ and is using exceptions. As stated here Zephyr has C++ support including exceptions.
Following the docs I set
But...
Hello.
I wrote adafruit's arduino compatible bootloader via J-link.
The write seems to have been successful.
However, after that, the nrf52840 does not work.
Do you...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1. with Zephyr
Im using Uart in DMA mode but have small doubts in implementation
1. what is the max size of buffer...
i am using nrf52832 dev kit. i ran ble app uart and found hat uart pins are set to
Tx: pin 8
Rx.: pin 6.
i want to change these pins to some other pin number but when...
Sorry I have some project with ncs over ubuntu 20.04
I'll do west build -b nrf52840dk_nrf52840 -p ==> it compile
when i Try to debug with west debug it work
when I try...
