Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi guys
For the nRF52833 and nRF52832 i can only find voltage range specifications for the GPIO peripheral .
Do those values also apply for the nRESET pin? (Since it could...
Hi,
I have a question regarding the nRF5340 Development Kit.
Is the SWF RF socket where the external antenna can be plugged into or an external antenna cannot be used...
We need to connect to multiple devices at once. We are controlling the SD via a serialised connection, with another chip controlling the parameters.
If we scan using interval...
I want 3 Axis Acceleration and Gyro data Via I2C bus, I have tried several ways and used some external libraries but nothing worked for me. And I am New to this so Please...
Hi,
I want to measure the duration of a single pulse using GPIOTE , PPI and a Timer with a NRF52840.
My initial idea was to have two capture tasks for the GPIO events...
Hi There,
I try to develop an application in intermittent conditions, it will off work frequently as for lacking the energy.
I try to resume the application from the last...
Essentially the title. Given that I have a BLE device which I have configured to have Legacy DFU services, and also customized the DFU service's UUID, how would I go about...
Hi,
I have nrf9160-DK and I am using NCS v1.6.1. I am trying to run HR Peripheral sample application on the nRF9160DK board.
I have flashed nrf52840 with hci_lpuart sample...
I am trying to using nRF52833 and nRF52840 as a BLE central to connect customer's BLE peripheral.
The attached screenshot is the service discovered by nRF connect Android...
Hello,
I am developing an application based on the BLE examples from the nrf5 sdk using he Segger Embedded Studio.
I am porting a library for a peripheral component and...
https://devzone.nordicsemi.com/f/nordic-q-a/80125/want-to-achieve-1-2-mbps-through-ble
Issue is in this link is not properly addressed . I want to work on BLE with good...
How much i can apply maximum and minimum voltage at Analog pin of nRF52832 controller IC? And Please also guide me is there any mention in the nRF52832 Datasheet.
Hi all,
I am using SDK = 15, softdevice = v6, chipset:nrf52810
I have used ble_app_uart and SAADC example code for one of my application, its working fine, and next i...
Hello,
I'm using nRF v1.5.1 SDK.
If I have my RX buffer to be of size say 6, and I transmit 7 bytes then my code will detect a full RX Buffer and go to the endrx_isr...
Hello,
Looking at the errata entry [78] TIMER: High current consumption when using timer STOP task only , I see that it recommended to use TASKS_SHUTDOWN instead of TASKS_STOP...
