Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I'm seeking clarification on what all can be ran on the network core. In the Network Core introduction section of the Working with nRF53 Series page, it mentions `the network...
Hi everyone,
As I mentioned in the subject, how many time do we wait for sending Start and Disable commands after Ready and End interrupts in transmit sequence of nRF52840...
hi, i have read nrf52832/40 product specs. i want to know about system off and system on modes. i am not getting what they mean pls explain in simple words.
infocenter.nordicsemi...
I want to use the usb dfu along with the buttonless ble dfu, how can I do so? I want to use the usb to have dfu and also work as a vitual com port? Can I simple merge both...
Hello
Can you provide customer with the API of the attachment( nRF_DTM.exe application)? They want to integrate this application into their mass production tools.
Hi everybody,
I am working with two custom boards with nrf52840 chip, using the examples of UART central/peripheral.
I set power TX of connection exactly as the example...
I have got the nrf5340dk,then i using the SES IDE of windows。I open the sample named "peripheral_nfc_pairing sample",and build the solution,then debug it .After those steps...
I am attempting to advertise two sets, one using coded PHY and one using 1M, currently using the master NCS branch (post v1.7.0-rc2 tag). This is on a custom board with an...
Hello,
I have got the exact same issue as described here: https://devzone.nordicsemi.com/f/nordic-q-a/58275/zigbee-reporting-not-work-while-using-multiple-endpoints/236706#236706...
I'm running FreeRTOS with default tickless idle mode (CPU is woken up by SysTick interrupt) on NET_CPU core.
If the TAD_S module (Trace and debug control) is not enabled...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
